Dell PowerEdge R6525 EMC Installation and Service Manual - Page 52

VGA module, Removing the VGA module

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

NOTE: Route the cable properly to prevent the cable from being pinched or crimped. 4. Using the Phillips #1 screwdriver, tighten the screws to secure the left control panel to the system. Figure 24. Installing the left control panel Next steps 1. Install the drive backplane cover. 2. If removed, install the air shroud. 3. Follow the procedure listed in After working inside your system on page 43. VGA module Removing the VGA module Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 42. 2. Follow the procedure listed in the Before working inside your system on page 43. 3. If installed, remove the front bezel. 4. Remove the backplane cover. 5. If installed, remove the air shroud. 6. Disconnect the VGA cable from the connector on the system board and open the cable latch. 7. Disconnect the right control panel cable from the system board and move it away to see the VGA module screw on the system. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. Route the cable properly when you replace it to prevent the cable from being pinched or crimped Steps 1. Using Phillips #2 screwdriver, remove the screw on the VGA module. 52 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
NOTE:
Route the cable properly to prevent the cable from being pinched or crimped.
4.
Using the Phillips #1 screwdriver, tighten the screws to secure the left control panel to the system.
Figure 24. Installing the left control panel
Next steps
1.
Install the drive backplane cover
.
2.
If removed,
install the air shroud
.
3.
Follow the procedure listed in
After working inside your system
on page 43.
VGA module
Removing the VGA module
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 42.
2.
Follow the procedure listed in the
Before working inside your system
on page 43.
3.
If installed,
remove the front bezel
.
4.
Remove the backplane cover
.
5.
If installed,
remove the air shroud
.
6.
Disconnect the VGA cable from the connector on the system board and open the cable latch.
7.
Disconnect the right control panel cable from the system board and move it away to see the VGA module screw on the system.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. Route the cable
properly when you replace it to prevent the cable from being pinched or crimped
Steps
1.
Using Phillips #2 screwdriver, remove the screw on the VGA module.
52
Installing and removing system components