Dell PowerEdge R6525 EMC Installation and Service Manual - Page 50

Installing the right control panel, Removing the left control panel

Get Dell PowerEdge R6525 PDF manuals and user guides View all Dell PowerEdge R6525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Installing the right control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 42. 2. Follow the procedure listed in Before working inside your system on page 43. Steps 1. Align and slide the right control panel in the slot on the system. 2. Connect the right control panel cable to the connector on the system board. 3. Route the right control panel cable through the side wall of the system. Close the cable latch and slide the cable into the clip. NOTE: Route the cable properly to prevent the cable from being pinched or crimped. 4. Using the Phillips #1 screwdriver, tighten the screws that secure the right control panel to the system. NOTE: The numbers on the image do not depict the exact steps. The numbers are for representation of sequence. Figure 22. Installing the right control panel Next steps 1. Install the drive backplane cover. 2. If removed, install the air shroud. 3. Follow the procedure listed in After working inside your system on page 43. Removing the left control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions on page 42. 2. Follow the procedure listed in the Before working inside your system on page 43. 50 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
Installing the right control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 42.
2.
Follow the procedure listed in
Before working inside your system
on page 43.
Steps
1.
Align and slide the right control panel in the slot on the system.
2.
Connect the right control panel cable to the connector on the system board.
3.
Route the right control panel cable through the side wall of the system. Close the cable latch and slide the cable into the clip.
NOTE:
Route the cable properly to prevent the cable from being pinched or crimped.
4.
Using the Phillips #1 screwdriver, tighten the screws that secure the right control panel to the system.
NOTE:
The numbers on the image do not depict the exact steps. The numbers are for representation of sequence.
Figure 22. Installing the right control panel
Next steps
1.
Install the drive backplane cover
.
2.
If removed,
install the air shroud
.
3.
Follow the procedure listed in
After working inside your system
on page 43.
Removing the left control panel
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
on page 42.
2.
Follow the procedure listed in the
Before working inside your system
on page 43.
50
Installing and removing system components