Dell PowerEdge T550 EMC Installation and Service Manual - Page 103

Removing the tape backup unit

Get Dell PowerEdge T550 PDF manuals and user guides View all Dell PowerEdge T550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

Figure 98. Installing the tape backup unit blank Next steps 1. If removed, install the front bezel. 2. Follow the procedure that is listed in After working inside your system. Removing the tape backup unit Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure that is listed in Before working inside your system. 3. Remove the air shroud. 4. If installed, remove the front bezel. 5. Disconnect the power and data cables from the tape backup unit. NOTE: Ensure that you note the routing of the power and data cable on the side of the system as you remove them from the system board and drive. Steps 1. Using a Phillips 2 screwdriver, remove the screw securing the tape backup unit to the system. 2. Slide the tape backup unit towards the front of the system. Installing and removing system components 103

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
Figure 98. Installing the tape backup unit blank
Next steps
1.
If removed,
install the front bezel
.
2.
Follow the procedure that is listed in
After working inside your system
.
Removing the tape backup unit
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure that is listed in
Before working inside your system
.
3.
Remove the air shroud
.
4.
If installed,
remove the front bezel
.
5.
Disconnect the power and data cables from the tape backup unit.
NOTE:
Ensure that you note the routing of the power and data cable on the side of the system as you remove them
from the system board and drive.
Steps
1.
Using a Phillips 2 screwdriver, remove the screw securing the tape backup unit to the system.
2.
Slide the tape backup unit towards the front of the system.
Installing and removing system components
103