Dell PowerSwitch S5212F-ON EMC SmartFabric OS10 User Guide Release 10.5.1 - Page 31

Starting from Release 10.5.1.0, SmartFabric OS10 comes with a single partition. Both the active and standby software images are stored in this partition. OS10 installation and upgrade procedures continue to work as usual. However, after you install 10.5.1.0 (or later) image, if you want to downgrade to 10.5.0.0 (or earlier) image, you must backup the configuration and license files. See Downgrade to Release 10.5.0.0 or earlier releases for more information. Supported platforms: For a list of currently supported Dell EMC switches for your SmartFabric OS10 release, see the SmartFabric OS10 Release Notes. The SmartFabric OS10 Release Notes are stored in the Dell Digital Locker (DDL) with SmartFabric OS10 software updates. Third-party software: Dell EMC does not support third-party software and drivers, community projects, code development, or implementation and development of security rules and policies. Configuration notes All Dell EMC PowerSwitches except MX-Series: ● If you pre-order a Dell EMC switch with OS10, you do not need to install a license. If you download OS10 on a trial basis, OS10 comes with a 120-day trial license. Purchase and install a perpetual license after the trial period expires. Once the trial period expires, the switch generates an error log on the console once every hour as follows: 1 2020-08-05T21:39:53.497121+00:00 OS10 dn_alm 648 - - Node.1-Unit.1:PRI [event], Dell EMC (OS10) %LADF_LIC_EVAL_PRD_NOTICE: Evaluation license time limit notice. Evaluation license expired. Please install a valid perpetual license. ● After you install OS10 and log in, install the OS10 license by following the instructions in the OS10 User Guide - Install OS10 License section. ● When you install a license using the Management VRF, only some file transfer methods like FTP, HTTP, localfs, SCP, SFTP, TFTP and USB are supported. For more information, see the Install OS10 license section in the OS10 User Guide. Switch with factory-installed OS10 A switch may come with OS10 Enterprise Edition factory-loaded. OS10 upgrades are available for download from the Dell Digital Locker (DDL). A factory-loaded OS10 image includes a perpetual license. On a factory-installed OS10 switch, after you log in, you can perform these tasks: ● Check the OS10 version. ● Upgrade the OS10 image. ● Re-install the license. If OS10 is pre-installed on a switch, zero-touch deployment (ZTD) is enabled by default. You can configure ZTD to install a new OS10 image. For more information about how to automate switch deployment, see Zero-touch deployment. NOTE: If a factory-installed OS10 image is deleted after booting into ONIE: Install OS mode, you must re-install the license. MX Ethernet I/O modules On Dell EMC PowerEdge MX Ethernet I/O modules, OS10 is factory-installed on the MX9116n Fabric Switching Engine and MX5108n Ethernet Switch. The MX7116n Fabric Expander Module does not support OS10 and functions as an unmanaged Ethernet repeater connected to a Fabric Switching Engine. Log in Connect a terminal emulator to the console serial port on the switch using a serial cable. Serial port settings are 115200 baud rate, 8 data bits, and no parity. To log in to an OS10 switch, power up and wait for the system to perform a power-on self-test (POST). Enter admin for both the default user name and user password. Change the default admin password after the first OS10 login. The system saves the new password for future logins. After you change the password through the CLI, use the write memory command to save the configuration. For example: OS10 login: admin Password: admin Last login: Sat Oct 6 00:25:33 UTC 2018 on ttyS0 Linux OS10 4.9.110 #1 SMP Debian 4.9.110-3+deb9u4 x86_64 Getting Started with Dell EMC SmartFabric OS10 31