Epson TM-m50II Web Config Reference Guide - Page 101
Title strings. Encryption, Authentication and Key
View all Epson TM-m50II manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 101 highlights
"ID Type" "ID" "Pre-Shared Key" "Confirm Pre-Shared Key" "Encapsulation" "Remote Gateway(Tunnel Mode)" "Security Protocol" "Algorithm Settings" Use the drop-down list to make a choice. "Distinguished Name" / "IP Address" / "FQDN" / "Email Address" / "Key ID" The values that can be entered depends on the selection for "ID Type cannot be used as the first character, regardless of the type selected. "Distinguished Name":ASCII, 1-255 characters. Must use [=]. "IP Address":IPv4, IPv6 "FQDN": ASCII(alphanumeric, dot, hyphen), 1-255 characters "Email Address": ASCII, 1-255 characters. Must use [@] and [=] is not usable. "Key ID": ASCII, 1-255 characters -Enter the passphrase. Usable string: ASCII code (0x20-0x7E) Max of 127 characters. - Same as "Pre-Shared Key". This item is displayed when "IKE Version" is "IKEv2". This item is enabled when "Enable this Group Policy" is enabled, "Access Control" is "IPsec", and "Authentication Method" for "Remote" is "Pre-Shared Key". This item is displayed when "IKE Version" is "IKEv2". This item is enabled when "Enable this Group Policy" is enable, "Access Control" is "IPsec" and "Authentication Method" of "Remote" is "Pre-Shared Key". This item is displayed when "IKE Version" is "IKEv2". This item is enabled when "Enable this Group Policy" is enable, "Access Control" is "IPsec" and "Authentication Method" of "Remote" is "Pre-Shared Key". - Same as "Pre-Shared Key". -Use the drop-down list to make a choice. "Transport Mode" / "Tunnel Mode" -It is possible to enter up to 39 characters. You can enter in the IPv4 and IPv6 formats You can enter the empty. You can not enter 255.255.255.255 and 0.0.0.0. -Use the drop-down list to make a choice. "ESP" / "AH" - If "Enable this Group Policy" is enabled and "Access Control" is "IPsec", it is possible to configure this item. - If "Enable this Group Policy" is enable, "Access Control" is "IPsec" and "Encapsulation" is "Tunnel Mode" ,it is possible to set this item. - If "Enable this Group Policy" is enabled and "Access Control" is "IPsec", it is possible to configure this item. Title strings. "IKE", "ESP" and "AH" are containted. - "IKE" "Encryption" "Encryption" "Authentication" Title strings. "Encryption", "Authentication" and "Key - Exchange" are contained. Use the drop-down list to choose from the following. "AES-CBC-128" / "AES-CBC-192" / "AES-CBC-256" / "3DES" / "Any" Use the drop-down list to choose from the following. "AES-CBC-128" / "AES-CBC-192" / "AES-CBC-256" / "AES-GCM-128" / "AES-GCM-192" / "AES-GCM-256" / "3DES" / "Any" Use the drop-down list to choose from the following. "SHA-1" / "SHA-256" / "SHA-384" / "SHA-512" / "MD5" / "Any" This item is displayed when "IKE Version" is "IKEv1". This item is enabled when "Enable this Group Policy" is enabled and "Access Control" is "IPsec".. This item is displayed when "IKE Version" is "IKEv2". This item is enabled when "Enable this Group Policy" is enable, "Access Control" is "IPsec". This item is enabled when "Enable this Group Policy" is enabled and "Access Control" is "IPsec". 101