Epson TM-m50II Web Config Reference Guide - Page 90

Confirm Settings Table 10-84 Button, Table 10-85 Setting Result

Page 90 highlights

10.4.4.2.6.2 Confirm Settings Page The confirmation page appears when the self-signed certificate is changed. 10.4.4.2.6.2.1 Image Setting Items Button Figure 10-37 Confirm Settings Page 10.4.4.2.6.2.2 Setting Items The settings entered on the previous page are shown for confirmation, after the message "Change the following settings". The following message is shown below the confirmed settings. "Communication will be shut down temporarily to enable the new settings." " You will not be able to access the network immediately after the settings are changed." 10.4.4.2.6.2.3 Button "OK" "Back" Items Table 10-84 Button Description Button at the bottom of the main frame to perform settings. Button at the bottom of the main frame to go back to the previous page. 10.4.4.2.6.3 Result Page The following result is shown in the main frame after the "OK" button is pressed. (Refer to Deleting a CA-signed certificate) 10.4.4.2.6.3.1 Result Page Table 10-85 Setting Result Items Description "Shutting down." This message is shown when the settings are completed. "Restarting communication may take a few minutes." The network shuts down in order to update. "If you want to change the settings, close the Web Config and check your IP address. Then enter your IP address in the browser to restart the Web Config." "Date and Time are not set" This message is shown when the printer's date and time are not set. "Setup failed." This message is shown if the settings fail. 90

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170

90
10.4.4.2.6.2
Confirm Settings Page
The confirmation page appears when the self-signed certificate is changed.
10.4.4.2.6.2.1
Image
Figure 10-37 Confirm Settings Page
10.4.4.2.6.2.2
Setting Items
The settings entered on the previous page are shown for confirmation, after the message “Change the following settings”.
The following message is shown below the confirmed settings.
“Communication will be shut down temporarily to enable the new settings.”
“ You will not be able to access the network immediately after the settings are changed.”
10.4.4.2.6.2.3
Button
Table 10-84 Button
10.4.4.2.6.3
Result Page
The following result is shown in the main frame after the “OK” button is pressed.
(Refer to Deleting a CA-signed certificate)
10.4.4.2.6.3.1
Result Page
Table 10-85 Setting Result
Items
Description
"OK"
Button at the bottom of the main frame to perform settings.
"Back"
Button at the bottom of the main frame to go back to the
previous page.
Items
Description
"Shutting down."
"Restarting communication may take a few minutes."
"If you want to change the settings, close the Web
Config and check your IP address. Then enter your IP
address in the browser to restart the Web Config."
This message is shown when the settings are completed.
The network shuts down in order to update.
"Date and Time are not set"
This message is shown when the printer’s date and time are not
set.
"Setup failed."
This message is shown if the settings fail.
Setting Items
Button