Epson TM-m50II Web Config Reference Guide - Page 66

Result

Page 66 highlights

10.3.4.2 Confirm Page 10.3.4.2.1 Image Display Items Button Figure 10-18 Confirm Page 10.3.4.2.2 Display Items The settings that were entered on the previous page are shown for confirmation after the "Change the following settings" message. The following message is shown below the confirmed settings: "Communication will stop temporarily to enable the new settings. You will not be able to access the network immediately after the settings are changed." 10.3.4.2.3 Button The following table shows the buttons on the page. "OK" "Back" Items Table 10-43 Button Description - Button at the bottom of the main frame to perform settings. - Button at the bottom of the main frame to go back to the previous page. 10.3.4.3 Result Page The result page is shown in the main frame after the "OK" button is pressed. An error page is shown when Wi-Fi LAN mode is set to IEEE802.11g in the printer. The page is shown when "Delete" is pressed on the previous page. 10.3.4.3.1 Image Setting Result Figure 10-19 Result Page 10.3.4.3.2 Setting Result Table 10-44 Setting Result Items Description "Shutting down." This message is shown if setup is successful. "Restarting communication may take a few minutes." "If you want to change the settings, close the Web Config and check your IP address. Then enter your IP address in the browser to restart the Web Config." "Setup complete." This message is shown when the delete operation is completed successfully. 66

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170

66
10.3.4.2
Confirm Page
10.3.4.2.1
Image
Figure 10-18 Confirm Page
10.3.4.2.2
Display Items
The settings that were entered on the previous page are shown for confirmation after the “Change the following settings” message.
The following message is shown below the confirmed settings: “Communication will stop temporarily to enable the new settings.
You will not be able to access the network immediately after the settings are changed.”
10.3.4.2.3
Button
The following table shows the buttons on the page.
Table 10-43 Button
10.3.4.3
Result Page
The result page is shown in the main frame after the “OK” button is pressed. An error page is shown when Wi-Fi LAN mode is set
to IEEE802.11g in the printer. The page is shown when “Delete” is pressed on the previous page.
10.3.4.3.1
Image
Figure 10-19 Result Page
10.3.4.3.2
Setting Result
Table 10-44 Setting Result
Items
Description
"OK"
- Button at the bottom of the main frame to perform settings.
"Back"
- Button at the bottom of the main frame to go back to the
previous page.
Items
Description
"Shutting down."
"Restarting communication may take a few minutes."
"If you want to change the settings, close the Web
Config and check your IP address. Then enter your IP
address in the browser to restart the Web Config."
This message is shown if setup is successful.
"Setup complete."
This message is shown when the delete operation is completed
successfully.
Button
Display Items
Setting Result