Epson TM-m50II Web Config Reference Guide - Page 41

Network Status

Page 41 highlights

10.1.2 Network Status In the Confirm Network Settings, you can confirm the product's network settings. 10.1.2.1 Top Page 10.1.2.1.1 Image Display Items Button Figure 10-2 Network Status 10.1.2.1.2 Tab "Network" and "Wi-Fi Direct" tabs are displayed on model that support wireless functions. You can switch between both sets of displayed information. 10.1.2.1.3 Display items The following table shows the display items for both model that support wireless functions and model that do not support wireless functions. Table 10-9 Displaying items (Network) Items Description Condition "Device Name" Shows the name of the printer. - "Connection Status" "Disconnect" / "10BASE-T Half Duplex" / "10BASE-T Full Shown when the wired LAN is used. Duplex" / "100BASE-TX Half Duplex" / "100BASE-TX Full Duplex" / "1000BASE-T Full Duplex"/ "Unknown" "Wi-Fi Disconnected" / "Searching for Wi-Fi" / Shown when the Wi-Fi is used. "W-Fi-xxxMbps" ("xx": "00" - "495") / "Unknown" "Disable" Shown when both the wired LAN and the wireless LAN are disabled (only Wi-Fi Direct Mode is used). "Signal Strength" "Obtain IP Address" "Set using BOOTP" "Excellent" / "Good" / "Fair" / "No Good" / "Unknown" "Auto" / "Manual" "Enable" / "Disable" Only shown when wireless LAN is used. Not shown while Wi-Fi Direct is used. Not shown when Connection Status is disabled. If "Obtain IP Address" is "Manual", this item is not shown. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170

41
10.1.2
Network Status
In the Confirm Network Settings, you can confirm the product’s network settings.
10.1.2.1
Top Page
10.1.2.1.1
Image
Figure 10-2 Network Status
10.1.2.1.2
Tab
“Network” and “Wi-Fi Direct” tabs are displayed on model that support wireless functions. You can switch between both sets of
displayed information.
10.1.2.1.3
Display items
The following table shows the display items for both model that support wireless functions and model that do not support wireless
functions.
Table 10-9 Displaying items (Network)
Items
Description
Condition
"Device Name"
Shows the name of the printer.
-
"Connection Status"
"Disconnect" / "10BASE-T Half Duplex" / "10BASE-T Full
Duplex" / "100BASE-TX Half Duplex" / "100BASE-TX Full
Duplex" / "1000BASE-T Full Duplex"/ "Unknown"
Shown when the wired LAN is used.
"Wi-Fi Disconnected" / "Searching for Wi-Fi" /
"W-Fi-xxxMbps" ("xx": "00" - "495") / "Unknown"
Shown when the Wi-Fi is used.
"Disable"
Shown when both the wired LAN and
the wireless LAN are disabled (only
Wi-Fi Direct Mode is used).
"Signal Strength"
"Excellent" / "Good" / "Fair" / "No Good" / "Unknown"
Only shown when wireless LAN is
used. Not shown while Wi-Fi Direct is
used.
"Obtain IP Address"
"Auto" / "Manual"
Not shown when Connection Status
is disabled.
"Set using BOOTP"
"Enable" / "Disable"
If "Obtain IP Address" is "Manual", this
item is not shown.
Display Items
Button