Home » HP Manuals » Desktops » HP Dc7900 » Manual Viewer

HP Dc7900 Service Reference Guide: HP Compaq dc7900 Business PC - Page 242

Storage, DPS Self-test, Storage Options, Emulation, Changes and Exit, Security, Drivelock Security,

UPC - 884962028483

Add to My Manuals
Save this manual to your list of manuals

Page 242 highlights

Table C-1 Numeric Codes and Text Messages (continued) Control panel message Description Recommended action 921-Device in PCI Express slot failed to initialize There is an incompatibility/problem with this Try rebooting the system. If the error device and the system or PCI Express Link reoccurs, the device may not work with this could not be retrained to an x1. system 1151-Serial Port A Address Conflict Detected Both external and internal serial ports are assigned to COM1. 1. Remove any serial port expansion cards. 2. Clear CMOS. 3. Reconfigure card resources and/or run Computer Setup or Windows utilities. 1152-Serial Port B Address Conflict Detected Both external and internal serial ports are assigned to COM2. 1. Remove any serial port expansion cards. 2. Clear CMOS. 3. Reconfigure card resources and/or run Computer Setup or Windows utilities. 1155-Serial Port Address Conflict Detected Both external and internal serial ports are assigned to same IRQ. 1. Remove any serial port expansion cards. 2. Clear CMOS. 3. Reconfigure card resources and/or run Computer Setup or Windows utilities. 1720-SMART Hard Drive Detects Imminent Failure Hard drive is about to fail. (Some hard drives 1. have a hard drive firmware patch that will fix an erroneous error message.) Determine if hard drive is giving correct error message. Enter Computer Setup and run the Drive Protection System test under Storage > DPS Self-test. 2. Apply hard drive firmware patch if applicable. (Available at http://www.hp.com/support.) 3. Back up contents and replace hard drive. 1796-SATA Cabling Error One or more SATA devices are improperly attached. For optimal performance, the SATA 0 and SATA 1 connectors must be used before SATA 2 and SATA 3. Ensure SATA connectors are used in ascending order. For one device, use SATA 0. For two devices, use SATA 0 and SATA 1. For three devices, use SATA 0, SATA 1, and SATA 2. 1797-SATA Drivelock is not supported in RAID mode. Drivelock is enabled on one or more SATA hard drives, and they cannot be accessed while the system is configured for RAID mode. Either remove the Drivelocked SATA device or disable the Drivelock feature. To disable the Drivelock feature, enter Computer Setup, change Storage > Storage Options > SATA Emulation to IDE, and select File > Save Changes and Exit. Reenter Computer Setup and select Security > Drivelock Security. For each listed Drivelock-capable SATA device, ensure Drivelock is Disabled. Lastly, change Storage > Storage Options > SATA Emulation back to RAID and select File > Save Changes and Exit. 1801-Microcode Patch Error Processor is not supported by ROM BIOS. 1. Upgrade BIOS to proper version. 2. Change the processor. 230 Appendix C POST Error Messages

Section	Page
Installing and Customizing the Software	13
Installing the Operating System	13
Installing or Upgrading Device Drivers	13
HP Backup and Recovery Manager	14
Computer Setup (F10) Utility	15
Computer Setup (F10) Utilities	15
Using Computer Setup (F10) Utilities	16
Computer Setup—File	17
Computer Setup—Storage	18
Computer Setup—Security	20
Computer Setup—Power	24
Computer Setup—Advanced	25
Recovering the Configuration Settings	28
Computer Diagnostic Features	29
HP Insight Diagnostics	29
Accessing HP Insight Diagnostics	29
Survey Tab	30
Test Tab	31
Status Tab	31
Log Tab	32
Help Tab	32
Saving and Printing Information in HP Insight Diagnostics	33
Downloading the Latest Version of HP Insight Diagnostics	33
Protecting the Software	33
HP Backup and Recovery Manager	34
Desktop Management	35
Initial Configuration and Deployment	35
HP Software Agent	36
Altiris Deployment Solution Agent	36
Remote System Installation	36
Software Updating and Management	37
HP Client Management Interface	37
HP SoftPaq Download Manager	38
HP System Software Manager	38
HP ProtectTools Security Manager	39
HP Client Automation Starter and Standard Editions	39
HP Client Automation Enterprise Edition	40
HP Client Manager from Symantec	40
Altiris Client Management Suite	41
HP Client Catalog for Microsoft System Center & SMS Products	41
HP Backup and Recovery Manager	41
Management Technology	42
Verdiem Surveyor	44
HP Proactive Change Notification	44
Subscriber’s Choice	44
Retired Solutions	44
ROM Flash	45
Remote ROM Flash	45
HPQFlash	45
Boot Block Emergency Recovery Mode	45
Replicating the Setup	46
Copying to Single Computer	46
Copying to Multiple Computers	47
Creating a Bootable Device	48
Supported USB Flash Media Device	48
Unsupported USB Flash Media Device	49
Dual-State Power Button	50
HP Web Site Support	51
Industry Standards	51
Asset Tracking and Security	51
Password Security	55
Establishing a Setup Password Using Computer Setup	55
Establishing a Power-On Password Using Computer Setup	55
Entering a Power-On Password	56
Entering a Setup Password	56
Changing a Power-On or Setup Password	56
Deleting a Power-On or Setup Password	57
National Keyboard Delimiter Characters	57
Clearing Passwords	58
DriveLock	58
Using DriveLock	58
DriveLock Applications	59
Smart Cover Sensor	59
Setting the Smart Cover Sensor Protection Level	59
Smart Cover Lock	60
Locking the Smart Cover Lock	60
Unlocking the Smart Cover Lock	60
Using the Smart Cover FailSafe Key	60
Cable Lock Provision	61
Fingerprint Identification Technology	61
Fault Notification and Recovery	61
Drive Protection System	61
Surge-Tolerant Power Supply	61
Thermal Sensor	62
Serial and Parallel ATA Drive Guidelines and Features	63
SATA Hard Drives	63
SATA Hard Drive Cables	64
SATA Data Cable	64
SATA Power Cable	64
PATA Device Information	65
ATA SMART Drives	65
Hard Drive Capacities	65
Identifying the Chassis, Routine Care, and Disassembly Preparation	66
Chassis Designations	66
Convertible Minitower (CMT)	66
Small Form Factor (SFF)	67
Ultra-Slim Desktop (USDT)	67
Electrostatic Discharge Information	68
Generating Static	68
Preventing Electrostatic Damage to Equipment	68
Personal Grounding Methods and Equipment	69
Grounding the Work Area	69
Recommended Materials and Equipment	69
Operating Guidelines	70
Routine Care	71
General Cleaning Safety Precautions	71
Cleaning the Computer Case	71
Cleaning the Keyboard	71
Cleaning the Monitor	72
Cleaning the Mouse	72
Service Considerations	72
Power Supply Fan	72
Tools and Software Requirements	72
Screws	73
Cables and Connectors	73
Hard Drives	73
Lithium Coin Cell Battery	74
Removal and Replacement Procedures Convertible Minitower (CMT) Chassis	75
Preparation for Disassembly	75
Unlocking the Smart Cover Lock	76
Smart Cover FailSafe Key	76
Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock	76
External Security Devices	78
Installing a Security Lock	78
Cable Lock	78
Padlock	79
HP Business PC Security Lock	80
Computer Access Panel	82
Front Bezel	83
Bezel Blanks	84
Cable Management	85
Cable Connections	86
Installing Additional Memory	87
DIMMs	87
DDR2-SDRAM DIMMs	87
Populating DIMM Sockets	88
Installing DIMMs	89
Expansion Cards	91
Drives	95
System Board Drive Connections	97
Drive Positions	98
Removing a Drive from a Drive Bay	99
Installing a 5.25-inch or 3.5-inch Drive into an External Drive Bay	103
Installing a 3.5-inch SATA Hard Drive into an Internal Drive Bay	105
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	107
Front I/O, USB, Power Switch Assembly	112
Speaker	113
Rear Chassis Fan	114
eSATA port assembly	115
Heatsink	116
Fan Shroud	117
Processor	118
Front Chassis Fan	119
Power Supply	120
System Board	121
Battery	122
Type 1 Battery Holder	123
Type 2 Battery Holder	123
Type 3 Battery Holder	124
Changing from a Minitower to a Desktop Configuration	125
Changing from a Desktop to a Minitower Configuration	127
Removal and Replacement Procedures Small Form Factor (SFF) Chassis	130
Preparation for Disassembly	130
Unlocking the Smart Cover Lock	131
Smart Cover FailSafe Key	131
Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock	131
External Security Devices	133
Installing a Security Lock	133
Cable Lock	133
Padlock	134
HP Business PC Security Lock	135
Front Bezel Security	137
Computer Access Panel	137
Front Bezel	138
Bezel Blanks	139
Installing Additional Memory	140
DIMMs	140
DDR2-SDRAM DIMMs	140
Populating DIMM Sockets	141
Installing DIMMs	142
Expansion Cards	144
Cable Management	149
Cable Connections	150
Drives	151
Drive Positions	151
Installing and Removing Drives	152
System Board Drive Connections	154
Removing an Optical Drive	155
Installing an Optical Drive into the 5.25-inch Drive Bay	156
Removing an External 3.5-inch Drive	159
Installing a Drive into the 3.5-inch External Drive Bay	162
Removing and Replacing the Primary 3.5-inch Internal SATA Hard Drive	164
Removing and Replacing a Removable 3.5-inch SATA Hard Drive	168
Fan Shroud	173
Front Fan Assembly	174
Hood Sensor	175
Power Switch Assembly	176
Front I/O Device	177
Speaker	177
Smart Cover Lock	178
Heatsink	179
Processor	180
Power Supply	181
System Board	183
Backwall	184
Battery	185
Type 1 Battery Holder	186
Type 2 Battery Holder	186
Type 3 Battery Holder	187
Using the Small Form Factor Computer in a Tower Orientation	188
Removal and Replacement Procedures Ultra-Slim Desktop (USDT) Chassis	190
Preparation for Disassembly	190
External Security Devices	191
Installing a Security Lock	191
Cable Lock	191
Padlock	192
HP Business PC Security Lock	192
Computer Access Panel	195
Front Bezel	196
Bezel Blank	197
Installing Additional Memory	198
SODIMMs	198
DDR2-SDRAM SODIMMs	198
Populating SODIMM Sockets	199
Installing SODIMMs	200
Cable Management	202
Cable Connections	203
Replacing the Optical Drive	203
Removing the Existing Optical Drive	203
Preparing the New Optical Drive	204
Installing the New Optical Drive	205
Optical Drive Connector	205
Hard Drive	207
Hard Drive Cage	211
Port Cover	212
Front Fan	213
Speaker	214
Rear Fan	215
Heatsink	216
Processor	217
System Board	218
Hood Sensor	220
Battery	220
Changing from Desktop to Tower Configuration	222
Connector Pin Assignments	224
Keyboard	224
Mouse	224
Ethernet BNC	224
Ethernet RJ-45	225
Ethernet AUI	225
Parallel Interface	226
Serial Interface, Powered and Non-Powered	226
USB	227
Microphone	227
Headphone	227
Line-in Audio	227
Line-out Audio	227
External Infrared Transceiver	228
Monitor	228
ATA/ATAPI (IDE) Standard Drive Cable	229
CD-ROM 50-Pin Connector	230
24-Pin Power	230
24-Pin MicroFit Power (CMT, SFF)	231
4-Pin Power (for CPU)	231
6-Pin Power (for CPU) (CMT, SFF)	231
SATA Data and Power	232
PCI Express	232
PCI Express	233
PCI Express Mini Card	234
DVI Connector	235
Power Cord Set Requirements	236
General Requirements	236
Japanese Power Cord Requirements	236
Country-Specific Requirements	237
POST Error Messages	238
POST Numeric Codes and Text Messages	239
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes	245
Troubleshooting Without Diagnostics	249
Safety and Comfort	249
Before You Call for Technical Support	249
Helpful Hints	250
Solving General Problems	252
Solving Power Problems	255
Solving Diskette Problems	256
Solving Hard Drive Problems	259
Solving Media Card Reader Problems	261
Solving Display Problems	263
Solving Audio Problems	267
Solving Printer Problems	268
Solving Keyboard and Mouse Problems	270
Solving Hardware Installation Problems	271
Solving Network Problems	273
Solving Memory Problems	276
Solving Processor Problems	277
Solving CD-ROM and DVD Problems	278
Solving USB Flash Drive Problems	280
Solving Front Panel Component Problems	281
Solving Internet Access Problems	281
Solving Software Problems	283
Contacting Customer Support	284
System Board and Riser Board Reference Designators	285
Specifications	291
CMT Specifications	291
SFF Specifications	292
USDT Specifications	293

Match case Limit results 1 per page

Control panel message

Description

Recommended action

921-Device in PCI Express slot failed to

initialize

There is an incompatibility/problem with this

device and the system or PCI Express Link

could not be retrained to an x1.

Try rebooting the system. If the error

reoccurs, the device may not work with this

system

1151-Serial Port A Address Conflict Detected

Both external and internal serial ports are

assigned to COM1.

Remove any serial port expansion

cards.

Clear CMOS.

Reconfigure card resources and/or run

Computer Setup or Windows utilities.

1152-Serial Port B Address Conflict Detected

Both external and internal serial ports are

assigned to COM2.

Remove any serial port expansion

cards.

Clear CMOS.

Reconfigure card resources and/or run

Computer Setup or Windows utilities.

1155-Serial Port Address Conflict Detected

Both external and internal serial ports are

assigned to same IRQ.

Remove any serial port expansion

cards.

Clear CMOS.

Reconfigure card resources and/or run

Computer Setup or Windows utilities.

1720-SMART Hard Drive Detects Imminent

Failure

Hard drive is about to fail. (Some hard drives

have a hard drive firmware patch that will fix

an erroneous error message.)

Determine if hard drive is giving correct

error message. Enter Computer Setup

and run the Drive Protection System test

under

Storage

DPS Self-test

Apply hard drive firmware patch

if applicable. (Available at

http://www.hp.com/

support

Back up contents and replace hard

drive.

1796-SATA Cabling Error

One or more SATA devices are improperly

attached. For optimal performance, the SATA

0 and SATA 1 connectors must be used

before SATA 2 and SATA 3.

Ensure SATA connectors are used in

ascending order. For one device, use SATA

0. For two devices, use SATA 0 and SATA 1.

For three devices, use SATA 0, SATA 1, and

SATA 2.

1797-SATA Drivelock is not supported in

RAID mode.

Drivelock is enabled on one or more SATA

hard drives, and they cannot be accessed

while the system is configured for RAID

mode.

Either remove the Drivelocked SATA device

or disable the Drivelock feature. To disable

the Drivelock feature, enter Computer Setup,

change

Storage

Storage Options

SATA

Emulation

IDE

, and select

File

Save

Changes and Exit

. Reenter Computer Setup

and select

Security

Drivelock Security

For each listed Drivelock-capable SATA

device, ensure Drivelock is

Disabled

. Lastly,

change

Storage

Storage Options

SATA

Emulation

back to

RAID

and select

File

Save Changes and Exit

1801-Microcode Patch Error

Processor is not supported by ROM BIOS.

Upgrade BIOS to proper version.

Change the processor.

Table C-1

Numeric Codes and Text Messages (continued)

230

Appendix C

POST Error Messages