HP Media Center 886c HP Media Center Desktop PCs - (English) Hardware User Gui - Page 62

HP Media Center 886c Manual

Get HP Media Center 886c PDF manuals and user guides View all HP Media Center 886c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Removing and replacing the preinstalled hard drive You must remove the hard drive from the chassis if you want to replace it with a higher capacity drive or if you want to safeguard your data when sending the computer out to be repaired. Removing and replacing the diskette drive or the 6-In-1 memory card reader To ensure that the drive fits properly into the chassis, be sure to purchase the replacement drive from HP. 1 Remove the drive cage. (See page 52.) 2 Remove the three screws that secure the hard drive 1 Remove the drive cage. (See page 52.) 2 Remove the two screws that secure the diskette drive in the drive cage: one screw on each side of the drive cage. (The screws for the 6-In-1 memory card reader were removed when the drive cage was removed.) replacement drive into the drive cage. in the drive cage: two screws on the latch side of the drive cage and one screw on the opposite side. in a safe location. 3 Pull the hard drive out, and store the drive and screws 3 Pull the drive out of the drive cage. Slide the 4 To replace the hard drive, reverse these steps. Make sure the jumper on the new hard drive is in the CS (Cable Select) position. (See figure on page 51). 4 For the diskette drive, attach the screws: one on each side of the drive cage. (The screws for the 6-In-1 memory card reader are replaced when the drive cage is replaced.) 5 Replace the drive cage. (See page 53.) 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
54
Removing and replacing the diskette drive
or the 6-In-1 memory card reader
To ensure that the drive fits properly into the chassis,
be sure to purchase the replacement drive from HP.
1
Remove the drive cage. (See page 52.)
2
Remove the two screws that secure the diskette drive
in the drive cage: one screw on each side of the
drive cage. (The screws for the 6-In-1 memory card
reader were removed when the drive cage was
removed.)
3
Pull the drive out of the drive cage. Slide the
replacement drive into the drive cage.
4
For the diskette drive, attach the screws: one on
each side of the drive cage. (The screws for the
6-In-1 memory card reader are replaced when the
drive cage is replaced.)
5
Replace the drive cage. (See page 53.)
Removing and replacing the
preinstalled hard drive
You must remove the hard drive from the chassis if you
want to replace it with a higher capacity drive or if you
want to safeguard your data when sending the computer
out to be repaired.
1
Remove the drive cage. (See page 52.)
2
Remove the three screws that secure the hard drive
in the drive cage: two screws on the latch side of the
drive cage and one screw on the opposite side.
3
Pull the hard drive out, and store the drive and screws
in a safe location.
4
To replace the hard drive, reverse these steps. Make
sure the jumper on the new hard drive is in the CS
(Cable Select) position. (See figure on page 51).