HP OmniBook 600C fw 02.00.02-1 and sw 06.00.02 HAFM Server Omnibook - Installa - Page 63

Sliding Shelf Installation for HAFM Server

Get HP OmniBook 600C - Notebook PC PDF manuals and user guides View all HP OmniBook 600C manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

10 Sliding Shelf Installation for HAFM Server This chapter contains information on how to install the sliding shelf for the HAFM server in an appropriate HP, or comparable, 19-inch Electronic Industries Association (EIA) rack, as follows: • hp 9000 series and hp 11000 series • hp rack system/e or 19-inch EIA rack NOTE: The installation of the HAFM server sliding shelf is not supported in the m-series cabinet. Installing the HAFM Server Sliding Shelf into a Supported Cabinet (Optional) Use the following procedure, as shown in Figure 10-1, to install sliding shelf brackets for the HAFM server: 1. Select a U slot above the switch. (It is recommended to select the U slot immediately above the switch. However, other U slots above the switch may also be used.) 2. On each rack rear column, locate the hole (1) that is 2 holes up from the EIA number of the selected U slot (3). 3. Line up this hole with the threaded hole on the sliding shelf bracket's side. 4. Using a screw (2), attach bracket (5) to the rack. 5. Attach another screw (4) loosely in the hole on the inside face of the mounting bracket (5). HAFM server installation guide 10-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
10–1
HAFM server installation guide
10
Sliding Shelf Installation for
HAFM Server
This chapter contains information on how to install the sliding shelf for the HAFM
server in an appropriate HP, or comparable, 19-inch Electronic Industries Association
(EIA) rack, as follows:
•
hp 9000 series and hp 11000 series
•
hp rack system/e or 19-inch EIA rack
NOTE:
The installation of the HAFM server sliding shelf is not supported in the m-series
cabinet.
Installing the HAFM Server Sliding Shelf into a
Supported Cabinet (Optional)
Use the following procedure, as shown in
Figure 10–1
, to install sliding shelf brackets
for the HAFM server:
1.
Select a U slot above the switch. (It is recommended to select the U slot
immediately above the switch. However, other U slots above the switch may also
be used.)
2.
On each rack rear column, locate the hole (
1
) that is 2 holes up from the EIA
number of the selected U slot (
3
).
3.
Line up this hole with the threaded hole on the sliding shelf bracket's side.
4.
Using a screw (
2
), attach bracket (
5
) to the rack.
5.
Attach another screw (
4
) loosely in the hole on the inside face of the mounting
bracket (
5
).