HP Scitex FB910 HP Scitex FB910 Printer Series - User Manual - Page 80

Report Individual Bad Jets, View current bad jets, Clear all bad jets

Get HP Scitex FB910 PDF manuals and user guides View all HP Scitex FB910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 80 highlights

3. When the calibration pattern has printed, the control panel displays a menu with the following options: • Report individual soft bad jets - enables you to report a "soft" bad jet, which can be automatically reenabled if AutoJet finds it working. • Report individual hard bad jets - enables you to report a "hard" bad jet, which will not be checked or reenabled by AutoJet. • Clear individual bad jets - enables you to clear (mark as good) a jet. • View current bad jets - lists the bad jets on a given printhead. • Clear all bad jets - clears (marks as good) all jets currently marked as unusable. A "soft" bad jet is a jet that you believe is temporarily out, based on past performance. A "hard" bad jet is a jet that you believe is permanently out. Select an option and follow the corresponding procedure below. Report Individual Bad Jets When you select Report Individual Bad Jets, the control panel displays the following prompt: Head 1: Press Proceed to report a bad jet. 4. Press , and ) to select a head number, then press ! (Proceed). The control panel displays a numeric keyboard that you can use to enter the number of the bad jet. 5. Enter the jet number, then press the Enter key. 6. When you are finished entering jet numbers, press the Esc key. The control panel displays the head selection message again. 4-18 Manual Calibrations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
4-18
Manual Calibrations
3.
When the calibration pattern has printed, the control panel
displays a menu with the following options:
•
Report individual soft bad jets
— enables you to
report a “soft” bad jet, which can be automatically
reenabled if AutoJet finds it working.
•
Report individual hard bad jets
— enables you to
report a “hard” bad jet, which will not be checked or
reenabled by AutoJet.
•
Clear individual bad jets
— enables you to clear
(mark as good) a jet.
•
View current bad jets
— lists the bad jets on a given
printhead.
•
Clear all bad jets
— clears (marks as good) all jets
currently marked as unusable.
A “soft” bad jet is a jet that you believe is temporarily out,
based on past performance. A “hard” bad jet is a jet that you
believe is permanently out.
Select an option and follow the corresponding procedure
below.
Report Individual Bad Jets
When you select Report Individual Bad Jets, the control
panel displays the following prompt:
Head 1:
Press Proceed to report a bad jet.
4.
Press
and
to select a head number, then press
(Proceed).
The control panel displays a numeric keyboard that you can
use to enter the number of the bad jet.
5.
Enter the jet number, then press the Enter key.
6.
When you are finished entering jet numbers, press the Esc
key.
The control panel displays the head selection message
again.