HP Scitex FB910 HP Scitex FB910 Printer Series - User Manual - Page 99

UV Lamps Idle Time, UV Lamps Warm-Up Time

Get HP Scitex FB910 PDF manuals and user guides View all HP Scitex FB910 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 99 highlights

Menus vention before printing can proceed). Expert mode presents Actions only, presents fewer "press Proceed" prompts after an Action has been addressed. The default is Novice mode. When in Expert mode, active Warnings and Actions can be displayed by selecting Warnings & Actions from the menu, since Warnings will not cause the ATTN key to appear in Expert mode. See "Overview" on page 5-2 for further information about Actions and Warnings. • Localization - sets English or Metric units of measure, time and date formats, and vacuum pressure units, for data displayed by the control panel. • Low Ink Warning - defines the amount of ink remaining in the ink box supply at which the printer will display a "low ink" message on the control panel. • Support Rollfed - enables or disables support for the rollfed media supply and takeup system. If the system does not appear to be working, check this menu item. • UV Lamps Idle Time - sets the amount of time the lamps will stay on after printing before they are automatically turned off by the printer. The idle time can be set from 1 to 10 minutes. Increase the idle time if you are printing several jobs and waiting for the lamps to warm up between prints. Decrease the idle time if printing single jobs. • UV Lamps Warm-Up Time - if both UV lamps have not warmed up completely when the first print begins printing, printing anomolies are likely to occur due to insufficientlycured ink. This option allows you to extend the warm-up period to ensure that both lamps have warmed up enough to cure the ink completely. The current warm-up period is displayed on the Front Page printer status pages. • Printer Name - displays a keypad to change the printer name displayed on the control panel and RIP. • Restore All Defaults - restores all Printer Configuration settings to their factory default values, and zeroes all registration data. After running this option, all printhead calibration values must be reestablished by running AutoSet or manual calibrations. 5-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
Menus
5-13
vention before printing can proceed).
Expert
mode presents
Actions only, presents fewer “press Proceed” prompts after
an Action has been addressed. The default is Novice mode.
When in Expert mode, active Warnings and Actions can be
displayed by selecting
Warnings & Actions
from the menu,
since Warnings will not cause the ATTN key to appear in
Expert mode. See “Overview” on page 5-2 for further infor-
mation about Actions and Warnings.
•
Localization
— sets
English
or
Metric
units of measure,
time and date formats, and vacuum pressure units, for data
displayed by the control panel.
•
Low Ink Warning
— defines the amount of ink remaining in
the ink box supply at which the printer will display a “low ink”
message on the control panel.
•
Support Rollfed
— enables or disables support for the roll-
fed media supply and takeup system. If the system does not
appear to be working, check this menu item.
•
UV Lamps Idle Time
— sets the amount of time the lamps
will stay on after printing before they are automatically turned
off by the printer.
The idle time can be set from 1 to 10 min-
utes. Increase the idle time if you are printing several jobs
and waiting for the lamps to warm up between prints.
Decrease the idle time if printing single jobs.
•
UV Lamps Warm-Up Time
— if both UV lamps have not
warmed up completely when the first print begins printing,
printing anomolies are likely to occur due to insufficiently-
cured ink. This option allows you to extend the warm-up
period to ensure that both lamps have warmed up enough to
cure the ink completely. The current warm-up period is dis-
played on the Front Page printer status pages.
•
Printer Name
— displays a keypad to change the printer
name displayed on the control panel and RIP.
•
Restore All Defaults
— restores all Printer Configuration
settings to their factory default values, and zeroes all regis-
tration data. After running this option, all printhead calibra-
tion values must be reestablished by running AutoSet or
manual calibrations.