HP dx7510 Service Reference Guide: HP Compaq dx7510/dx7518 Business PC - Page 40

Preparation for Disassembly

Get HP dx7510 - Microtower PC PDF manuals and user guides View all HP dx7510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Preparation for Disassembly 1. Close any open software applications. 2. Exit the operating system. 3. Remove any diskette or compact disc from the computer. 4. Turn off the computer and any peripheral devices that are connected to it. CAUTION: Turn off the computer before disconnecting any cables. CAUTION: Regardless of the power-on state, voltage is always present on the system board as long as the system is plugged into an active AC outlet. In some systems the cooling fan is on even when the computer is in the "Standby," or "Suspend" modes. The power cord should always be disconnected before servicing a unit. 5. Disconnect the power cord from the electrical outlet and then from the computer. 6. Disconnect all peripheral device cables from the computer. NOTE: During disassembly, label each cable as you remove it, noting its position and routing. Keep all screws with the units removed. CAUTION: The screws used in the computer are of different thread sizes and lengths; using the wrong screw in an application may damage the unit. 32 Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
Preparation for Disassembly
1.
Close any open software applications.
2.
Exit the operating system.
3.
Remove any diskette or compact disc from the computer.
4.
Turn off the computer and any peripheral devices that are connected to it.
CAUTION:
Turn off the computer before disconnecting any cables.
CAUTION:
Regardless of the power-on state, voltage is always present on the system board as
long as the system is plugged into an active AC outlet. In some systems the cooling fan is on even
when the computer is in the “Standby,” or “Suspend” modes. The power cord should always be
disconnected before servicing a unit.
5.
Disconnect the power cord from the electrical outlet and then from the computer.
6.
Disconnect all peripheral device cables from the computer.
NOTE:
During disassembly, label each cable as you remove it, noting its position and routing.
Keep all screws with the units removed.
CAUTION:
The screws used in the computer are of different thread sizes and lengths; using the
wrong screw in an application may damage the unit.
32
Chapter 6
Removal and Replacement Procedures Microtower (MT) Chassis