HP dx7510 Service Reference Guide: HP Compaq dx7510/dx7518 Business PC - Page 58

Installing an Optical Drive into the 5.25-inch Drive Bay, on Preparation for Disassembly

Get HP dx7510 - Microtower PC PDF manuals and user guides View all HP dx7510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

NOTE: To install an optical drive, refer to Installing an Optical Drive into the 5.25-inch Drive Bay on page 50. Installing an Optical Drive into the 5.25-inch Drive Bay To install an optional 5.25-inch optical drive: 1. Prepare the computer for disassembly (Preparation for Disassembly on page 32). 2. Remove the access panel (Access Panel on page 33). 3. If you are installing a drive in a bay covered by a bezel blank, remove the front bezel then remove the bezel blank. 4. If you are adding a drive to an empty lower optical drive bay, you must remove the knockout plate from the bay. To do so, insert a flat screwdriver into the knockout plate slot and rotate the screwdriver to break the knockout plate out of the chassis. Discard the knockout plate. 5. If the new drive has screws installed on the sides of the drive, remove the screws before inserting the drive into the chassis. 6. Slide the drive in through the front of the chassis (1) until the screw holes on the drive are aligned with the screw holes on the drive cage and install the two M3 metric retainer screws (2) as shown in the following illustration. NOTE: Extra drive retainer screws are provided on the interior of the front bezel if needed. The M3 metric retainer screws for optical drives are black. Refer to Installing Additional Drives on page 47 for an illustration of the retainer screws location. Figure 6-19 Installing the Optical Drive 7. If the system configuration includes only one optical drive, connect the SATA data cable to the white system board connector labeled SATA2. If you are adding a second optical drive, connect the SATA data cable to the orange system board connector labeled SATA4. 50 Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
NOTE:
To install an optical drive, refer to
Installing an Optical Drive into the 5.25-inch Drive Bay
on page
50
.
Installing an Optical Drive into the 5.25-inch Drive Bay
To install an optional 5.25-inch optical drive:
1.
Prepare the computer for disassembly (
Preparation for Disassembly
on page
32
).
2.
Remove the access panel (
Access Panel
on page
33
).
3.
If you are installing a drive in a bay covered by a bezel blank, remove the front bezel then remove
the bezel blank.
4.
If you are adding a drive to an empty lower optical drive bay, you must remove the knockout plate
from the bay. To do so, insert a flat screwdriver into the knockout plate slot and rotate the
screwdriver to break the knockout plate out of the chassis. Discard the knockout plate.
5.
If the new drive has screws installed on the sides of the drive, remove the screws before inserting
the drive into the chassis.
6.
Slide the drive in through the front of the chassis
(1)
until the screw holes on the drive are aligned
with the screw holes on the drive cage and install the two M3 metric retainer screws
(2)
as shown
in the following illustration.
NOTE:
Extra drive retainer screws are provided on the interior of the front bezel if needed. The
M3 metric retainer screws for optical drives are black. Refer to
Installing Additional Drives
on page
47
for an illustration of the retainer screws location.
Figure 6-19
Installing the Optical Drive
7.
If the system configuration includes only one optical drive, connect the SATA data cable to the
white system board connector labeled SATA2. If you are adding a second optical drive, connect
the SATA data cable to the orange system board connector labeled SATA4.
50
Chapter 6
Removal and Replacement Procedures Microtower (MT) Chassis