Home » Honeywell Manuals » Security Monitors & Recorders » Honeywell NX4S1 » Manual Viewer

Honeywell NX4S1 User Guide - Page 41

Configuring the Doors, 2.4.1 Reader Tab, Reader Tab

Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Configuring via the Web Server Configuring the System 2.4 Configuring the Doors Each NetAXS™ panel supports four doors. For each door, you must configure the readers, inputs, and outputs. At Configuration > Doors in the task menu at the left margin of the NetAXS™ screen, click 1 to display the Door Configuration screen for door 1. Follow the same procedures below for doors 2, 3, and 4 for each panel. 2.4.1 Reader Tab A reader is a device that reads cards and either grants or denies access at the door. Click the Reader tab: Figure 2-11: Configuration > Doors > Reader > General Tab The Reader tab enables you to: • Define the time zone during which the reader will be disabled. When the reader is disabled, neither exit nor entry by Card and PIN mode or Card or PIN mode is allowed. Also, free egress is not allowed. Note: Should a conflict arise among the time zones set in the Access Mode Time Zones box on the Reader > General tab, priority is given to the time zone that is highest in the list of time zones displayed on the tab. Therefore, the Disabled time zone has highest priority, and the Card Only time zone has lowest priority. NetAXS™ Access Control Unit User's Guide, Document 800-04410, Revision A 31

Section	Page
Front Cover	1
Table of Contents	3
List of Figures	5
List of Tables	7
What’s New in Release 3.1.8	9
Dynamic Screens and Performance Enhancements	9
Multi-language Support	9
CSV Reports and Card Upgrade	10
Reverse IP	10
Connecting to the Web Server	11
1.1 Overview	11
1.2 Connecting to the Web Server	12
1.3 Reading the Select Panel	17
Configuring via the Web Server	19
2.1 Overview	20
2.2 Configuring the System	21
2.2.1 Host/Loop Communications Tab	21
2.2.2 General Tab	24
2.2.3 File Management Tab	27
2.2.4 Network Tab	30
2.2.5 Site Codes Tab	31
2.2.6 Downstream Devices Tab	33
2.3 Configuring Time Management	34
2.3.1 Current Time Tab	34
2.3.2 Time Zones Tab	36
2.3.3 Holidays Tab	39
2.4 Configuring the Doors	41
2.4.1 Reader Tab	41
2.4.2 Outputs Tab	48
2.4.3 Inputs Tab	52
2.5 Configuring Access Levels	55
2.6 Maintaining Cards	57
2.6.1 Adding New Cards	57
2.6.2 Displaying and Modifying Cards	59
2.6.3 Deleting Cards	60
2.6.4 Displaying Reports	61
2.7 Configuring Other I/O & Groups Tab	62
2.7.1 Inputs Tab	62
2.7.2 Outputs Tab	65
2.7.3 Groups Tab	67
2.8 Configuring Interlocks	69
2.9 Configuring Users	71
Configuring via WIN-PAK	75
3.1 Overview	75
3.2 Adding a New NetAXS™ Panel	76
3.2.1 Creating the Panel with Quick Start Wizard	76
3.2.2 Configuring the Panel Manually	77
Monitoring NetAXS™ Status	85
4.1 Overview	85
4.2 Monitoring Alarms	86
4.3 Monitoring Events	89
4.4 Monitoring Inputs	92
4.5 Monitoring Outputs	95
4.6 Monitoring System Status	97
Upgrading NetAXS™ Firmware	99
A.1 Overview	99
A.2 NetAXS™ Release 3.1.8 Upgrade Procedure	99
A.2.1 Planning the Upgrade	99
A.2.2 Mixed Revision Loops	99
A.2.3 Uploading Data from the Panel	100
A.2.4 Upgrades to Gateway vs. Multi-drop Panels	100
A.2.5 Upgrade Notes	102
A.2.6 Clearing the Cache in the Internet Browsers Used by the NetAXS™ Web Server	103
To clear the cache using Internet Explorer 7 (IE7):	103
To clear cache using Internet Explorer 6 (IE6):	103
To clear cache using Firefox 2 and Firefox 3:	103
Index	105

Match case Limit results 1 per page

Configuring via the Web Server

Configuring the System

NetAXS™ Access Control Unit User’s Guide

Document 800-04410, Revision A

2.4

Configuring the Doors

Each NetAXS™ panel supports four doors. For each door, you must configure the readers, inputs, and

outputs.

At Configuration > Doors in the task menu at the left margin of the NetAXS™ screen, click

display the Door Configuration screen for door 1. Follow the same procedures below for doors 2, 3,

and 4 for each panel.

2.4.1

Reader Tab

A reader is a device that reads cards and either grants or denies access at the door.

Click the

Reader

tab:

Figure 2-11:

Configuration > Doors > Reader > General Tab

The Reader tab enables you to:

•

Define the time zone during which the reader will be disabled. When the reader is disabled,

neither exit nor entry by Card and PIN mode or Card or PIN mode is allowed. Also, free egress

is not allowed.

Note:

Should a conflict arise among the time zones set in the Access Mode Time Zones box on

the Reader > General tab, priority is given to the time zone that is highest in the list of time

zones displayed on the tab. Therefore, the Disabled time zone has highest priority, and the Card

Only time zone has lowest priority.