IBM 25R0012 User Guide - Page 26

Install, Device, Drivers, Connect, Enclosure's, External, Interface, Server

Get IBM 25R0012 - LTO Generation 3 SCSI Tape Drive PDF manuals and user guides
UPC - 000435800176
View all IBM 25R0012 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

__ 6. Disconnect the power cord from both the host and the electrical outlet. Install Device Drivers For information about installing device drivers, refer to the documentation for your server and/or Operating System. Connect the Enclosure's External SCSI Interface to the Server __ 1. Connect an external SCSI bus cable to both the enclosure and the server (for the location of the connectors, refer to the documentation for your enclosure and server). __ 2. Run the appropriate SCSI attachment verification procedure from your server (for instructions, refer to the IBM Ultrium Device Drivers Installation and User's Guide). If you want to power a device on or off while it is connected to the same SCSI bus as the drive, you can do so if, during the power-on cycle, you quiesce all devices (including the drive) on the bus. 10 IBM 400/800GB LTO3 Tape Drive User's Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
__
6.
Disconnect
the
power
cord
from
both
the
host
and
the
electrical
outlet.
Install
Device
Drivers
For
information
about
installing
device
drivers,
refer
to
the
documentation
for
your
server
and/or
Operating
System.
Connect
the
Enclosure’s
External
SCSI
Interface
to
the
Server
__
1.
Connect
an
external
SCSI
bus
cable
to
both
the
enclosure
and
the
server
(for
the
location
of
the
connectors,
refer
to
the
documentation
for
your
enclosure
and
server).
__
2.
Run
the
appropriate
SCSI
attachment
verification
procedure
from
your
server
(for
instructions,
refer
to
the
IBM
Ultrium
Device
Drivers
Installation
and
User’s
Guide
).
If
you
want
to
power
a
device
on
or
off
while
it
is
connected
to
the
same
SCSI
bus
as
the
drive,
you
can
do
so
if,
during
the
power-on
cycle,
you
quiesce
all
devices
(including
the
drive)
on
the
bus.
10
IBM
400/800GB
LTO3
Tape
Drive
User’s
Guide