IBM 72336RU User Manual - Page 77

Save User Account Settings in BMC, Save Network Settings in BMC

Get IBM 72336RU PDF manuals and user guides View all IBM 72336RU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Select this choice to set the DHCP control. DHCP Enabled is the default setting. If you select Use Static IP, use IP Address to set the address. v IP Address Select this choice to set the static IP address for the BMC. The initial value is assigned by the DHCP server or is 169.254.0.2. v Subnet Mask Select this choice to set the subnet mask for the BMC. The default is 255.255.0.0. v Gateway Select this choice to set the gateway for the BMC. The default is 0.0.0.0. v Save Network Settings in BMC Select this choice to save any changes to the network configuration. - BMC System Event Log Select this choice to view the BMC system event log, which contains all system-error and warning messages that have been generated. Use the arrow keys to move among pages in the log. See the Problem Determination and Service Guide on the IBM System x Documentation CD for instructions. Select Clear error logs to clear the BMC system event log. Note: Use the IBM Remote Supervisor Adapter II system event log or run the diagnostic programs for more information about the error codes. - User Account Settings Select this choice to view and change the BMC user account information. You can define up to four user accounts. By default, two user accounts are defined: NULL and USERID. The USERID user account is enabled by default. The password for the USERID user account is PASSW0RD. - UserID Select this choice to view or change settings for user accounts 1, 2, 3, and 4. v UserID Select this choice to enable or disable the user account. The NULL user account is disabled by default. v Username Select this choice to view or change the user name. v Password Select this choice to set the password. v Confirm Password Select this choice to confirm the password. v Privilege Limit Select this choice to set the level of access. v Save User Account Settings in BMC Select this choice to save any changes to the user account configuration. v Event/Error Logs Select this choice to view or clear error logs. This choice is available on the full Configuration/Setup Utility menu only. - POST Error Log Chapter 3. Configuring the server 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Select this choice to set the DHCP control.
DHCP Enabled
is the default
setting. If you select
Use Static IP
, use
IP Address
to set the address.
v
IP Address
Select this choice to set the static IP address for the BMC. The initial
value is assigned by the DHCP server or is 169.254.0.2.
v
Subnet Mask
Select this choice to set the subnet mask for the BMC. The default is
255.255.0.0.
v
Gateway
Select this choice to set the gateway for the BMC. The default is 0.0.0.0.
v
Save Network Settings in BMC
Select this choice to save any changes to the network configuration.
-
BMC System Event Log
Select this choice to view the BMC system event log, which contains all
system-error and warning messages that have been generated. Use the
arrow keys to move among pages in the log. See the
Problem
Determination and Service Guide
on the IBM
System x Documentation
CD
for instructions. Select
Clear error logs
to clear the BMC system event log.
Note:
Use the IBM Remote Supervisor Adapter II system event log or run
the diagnostic programs for more information about the error codes.
-
User Account Settings
Select this choice to view and change the BMC user account information.
You can define up to four user accounts. By default, two user accounts are
defined: NULL and USERID. The USERID user account is enabled by
default. The password for the USERID user account is
PASSW0RD
.
-
UserID
Select this choice to view or change settings for user accounts 1, 2, 3, and
4.
v
UserID
Select this choice to enable or disable the user account. The NULL user
account is disabled by default.
v
Username
Select this choice to view or change the user name.
v
Password
Select this choice to set the password.
v
Confirm Password
Select this choice to confirm the password.
v
Privilege Limit
Select this choice to set the level of access.
v
Save User Account Settings in BMC
Select this choice to save any changes to the user account configuration.
v
Event/Error Logs
Select this choice to view or clear error logs.
This choice is available on the full Configuration/Setup Utility menu only.
–
POST Error Log
Chapter 3. Configuring the server
65