JVC SR-VD400US Instruction Manual - Page 35

4 Input receiving channel number The guide channel number, which is FUNCTION SET UP TUNER SET UP INITIAL SET UP CLOCK SET GUIDE CHANNEL OTHER assigned to the TV or GUIDE CH 12 VCR CH - - cable station for the PlusCode number that you entered in step 3, will appear MENU EXIT OK SELECT WITH ARROW KEYS SELECT THEN PRESS [OK] automatically on the Guide Channel Set Up screen. Press @ # to input the number of the channel on which the broadcast for the PlusCode number is received on the VCR or cable box, then press OK. ● The Guide Channel Set screen appears only when you input the PlusCode number of a station for which the guide channel number has not been set previously. ● If you receive your channels with a cable box and if you have properly set your Controller, "CABLE CH" appears in place of "VCR CH". If not, refer to pages 15 - 17. In that case, it is possible to change the channel by 10 channels by pressing and holding @ #. 5 Check program data The PlusCode number you entered and the corresponding timer recording program is displayed on the Program screen. Check to make sure it is accurate. TIMER PROGRAM PLUSCODE NO. 12345 START TIME 8:00 PM STOP TIME 10:00 PM DATE 12/24/03 (WED) REC SPEED STD (SP) DAILY/WEEKLY EVERY WED CH 12 CH SOURCE CATV CONFIRM CANCEL PROG. EXIT START STOP DATE CH SET PROGRAM WITH [+/-, REC SPEED, 8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM" ● To change the start/stop time, date or channel setting, press the corresponding buttons to change the settings; START +/-, STOP +/-, DATE +/-, TV/VCR CH +/-. ● To timer-record daily or weekly serials, press DAILY (number "8") or WEEKLY (number "9"). "MON - FRI", "MON - SAT", "SUN - SAT" or "EVERY _ _ _" appears on the Program screen. Pressing the button again makes each corresponding display disappear. ● For the "SOURCE" setting, refer to page 39. ● If you made a mistake, press BACK to access the VCR Plus+ screen again and input the correct PlusCode number. 6 Set recording speed Press REC SPEED to set the recording speed. EN 35 7 Return to normal screen Press @ # to move the arrow to "CONFIRM", then press OK. "PROGRAM COMPLETED PRESS [TIMER] TO ENTER TIMER STANDBY MODE" appears on the screen, then press OK to return to normal screen. 8 Engage timer recording standby mode Press TIMER (‰). The VCR turns off automatically and "‰" is displayed on the front display panel. To use the VCR while it is in timer recording standby mode Press TIMER (‰) to cancel the timer recording standby mode, then press POWER to turn on the VCR. DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER (‰) after you use the VCR; otherwise, you cannot record the broadcasts you want. ● When "AUTO TIMER" (੬ pg. 59) is set to "ON", the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER (‰) to engage or disengage the timer recording standby mode. IMPORTANT If you have moved to a different area or if a broadcasting station's channel number has been changed, the wrong VCR CH or CABLE CH number will be displayed on the Program screen in step 5. When this happens, set the correct guide channel number for that station. (੬ pg. 36, "Changing VCR Plus+ Setting") NOTES: ● Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time is lost if it lasts for more than 10 minutes. As a result, when the power is supplied again to this VCR after the power failure, the following will take place. 1. This VCR starts Auto Clock Set automatically to restore the clock time. 2. If the clock time is restored correctly and "AUTO TIMER" is set to "ON", each timer program you have made will start at its start time unless its end time has elapsed. ● If the tape reaches its end during timer recording and " #" blink. ● To timer-record cable channels received through a cable box, be sure to keep the cable box turned on.