JVC SR-VD400US Instruction Manual - Page 42

PRO HD SYSTEM, PRO HD System Playback

Get JVC SR-VD400US - D-vhs Recorder/player, Pro-hd Player PDF manuals and user guides View all JVC SR-VD400US manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

42 EN PRO HD System Playback ● Turn on the VCR and the TV, and select the AV mode on the TV. ● Set the VCR/TV/CABLE/DBS selector on the Remote to "VCR". POWER 1 2 STOP/EJECT (7/0) IN F-1 VCR CABLE TV /DBS + REW ( ) FF ( ) POWER PRO HD SYSTEM This PRO HD system can perform playback of the D-VHS tape recorded by the MPEG2-TS signal. This VCR can check the tape condition during playback (and recording), and realizes the best possible pictures. Please refer to next page, when you playback the tape on which the password was set up. 1 Load a D-VHS cassette Make sure the window side is up, the rear label side is facing you and the arrow on the front of the cassette is pointing towards the VCR. Do not apply too much pressure when inserting. ● The VCR turns on automatically. ● The tape will run for a few seconds while the VCR searches for the tape number. If the tape number is found, it will be shown on the TV screen if "SUPERIMPOSE" is set to "ON" (੬ pg. 59). ● The counter is reset automatically, however, it is not completely reset to "0:00:00". ● If the cassette's record safety tab has been removed, playback begins automatically. 2 Start playback Press PLAY ( 3 ). ● Tape speed is automatically detected. REW(1) 2 FF(¡) STOP(7) To stop playback Press STOP ( 7 ) on the Remote or STOP/EJECT ( 7/0 ) on the front panel. To rewind the tape (when it is not running) Press REW ( 1 ). To fast-forward (when it is not running) Press FF ( ¡ ). To eject the tape Press STOP/EJECT ( 7/0 ) on the front panel when the tape is not running. ● You can also eject the cassette when the VCR is turned off. To turn off the VCR Press POWER.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
42
EN
IN F-1
+
POWER
STOP/EJECT
(
7
/
0
)
1
2
REW (
)
FF (
)
PRO HD SYSTEM
PRO HD System
Playback
This PRO HD system can perform playback of the D-VHS tape
recorded by the MPEG2-TS signal.
This VCR can check the tape condition during playback (and
recording), and realizes the best possible pictures.
Please refer to next page, when you playback the
tape on which the password was set up.
1
Load a D-VHS cassette
Make sure the window side is up, the rear label
side is facing you and the arrow on the front of
the cassette is pointing towards the VCR.
Do not apply too much pressure when inserting.
●
The VCR turns on automatically.
●
The tape will run for a few seconds while the
VCR searches for the tape number. If the tape
number is found, it will be shown on the TV
screen if “SUPERIMPOSE” is set to “ON”
(
±
pg. 59).
●
The counter is reset automatically, however, it
is not completely reset to “0:00:00”.
●
If the cassette’s record safety tab has been
removed, playback begins automatically.
2
Start playback
Press
PLAY (
3
)
.
●
Tape speed is automatically detected.
To stop playback
Press
STOP (
7
)
on the Remote or
STOP/EJECT
(
7
/
0
)
on the front panel.
To rewind the tape (when it is not running)
Press
REW (
1
)
.
To fast-forward (when it is not running)
Press
FF (
¡
)
.
To eject the tape
Press
STOP/EJECT (
7
/
0
)
on the front panel when the
tape is not running.
●
You can also eject the cassette when the VCR is turned
off.
To turn off the VCR
Press
POWER
.
VCR
TV
CABLE
/DBS
POWER
REW(
1
)
2
FF(
¡
)
STOP(
7
)
●
Turn on the VCR and the TV, and select the AV
mode on the TV.
●
Set the
VCR/TV/CABLE/DBS
selector on the
Remote to “VCR”.