JVC SR-VD400US Instruction Manual - Page 39

8 Set recording speed Press REC SPEED to set the recording speed. 9 Return to normal screen Press @ # to move the arrow to "CONFIRM", then press OK. "PROGRAM COMPLETED PRESS [TIMER] TO ENTER TIMER STANDBY MODE" appears on the screen, then press OK to return to normal screen. 0 Engage timer recording standby mode Press TIMER (‰). The VCR turns off automatically and "‰" is displayed on the front display panel. To timer-record daily or weekly serials Press DAILY (number "8") or WEEKLY (number "9") anytime during steps 4 through 8. "MON - FRI", "MON - SAT", "SUN - SAT" or "EVERY _ _ _" appears on the Program screen. ● Pressing the button again makes the corresponding indication disappear. To use the VCR while it is in timer recording standby mode Press TIMER (‰) to cancel the timer recording standby mode, then press POWER to turn on the VCR. DO NOT forget to put the VCR into timer recording standby mode again by pressing TIMER (‰) after you use the VCR; otherwise, you cannot record the broadcast you want. ● When "AUTO TIMER" (੬ pg. 59) is set to "ON", the timer recording standby mode is automatically engaged when the VCR is turned off. It is temporarily canceled when the VCR is turned on. You do not have to press TIMER (‰) to engage or disengage the timer recording standby mode. EN 39 NOTES: ● Even if a power failure occurs, the VCR keeps your timer programs. However, the clock time is lost if it lasts for more than 10 minutes. As a result, when the power is supplied again to this VCR after the power failure, the following will take place. 1. This VCR starts Auto Clock Set automatically to restore the clock time. 2. If the clock time is restored correctly and "AUTO TIMER" is set to "ON", each timer program you have made will start at its start time unless its end time has elapsed. ● Programs that start after midnight must have the next day's date. ● After timer recording is completed, the VCR turns off automatically. ● You can program the timer recording while a regular recording is in progress; the menu screens will not be recorded. ● If the tape reaches its end during timer recording and " #" blink. ● To timer-record cable or satellite channels, be sure to keep the cable box or DBS receiver turned on. ATTENTION FOR DBS RECEIVER USERS If you are using a DBS TIMER PROGRAM receiver (unless "INPUT CH" is set to "OFF" on START TIME 8:00 PM STOP TIME 10:00 PM DATE 12/24/03 (WED) CH 110 CH DBS Receiver Set screen ੬ pg. 19), the band indication (TV, CATV or DBS) appears under the REC SPEED STD (SP) DAILY/WEEKLY EVERY WED SOURCE DBS CONFIRM CANCEL PROG. EXIT START STOP DATE CH SET PROGRAM WITH [+/-, REC SPEED,7=DBS, 8=DAILY, 9=WEEKLY] THEN PRESS "CONFIRM" channel number indication (SOURCE). TV :To timer-record a regular TV broadcast received on the VCR. CATV :To timer-record a cable TV broadcast received on the VCR, or through a cable box (unless "INPUT CH" is set to "OFF" on Cable Set Up screen ੬ pg. 16). DBS :To timer-record a satellite broadcast received through a DBS receiver. NOTE: If "BAND" is set to "TV" on the Tuner Set Up Screen (੬ pg. 14) and "INPUT CH" is set to "OFF" on Cable Set Up screen (੬ pg. 16), "CATV" will not be displayed on the Program screen; If "BAND" is set to "CATV" or "INPUT CH" is set to "ON" on Cable Set Up screen, "TV" will not be displayed. If the channel number entered requires that the band be set, "7=DBS" is displayed on the screen. If this happens, press the Number key "7 (DBS)" to select "DBS".