Konica Minolta AccurioPress C14000 Watkiss PowerSquare R2L User Manual - Page 64

MAIN CONTROL - No, See Clear a Stitch

Get Konica Minolta AccurioPress C14000 PDF manuals and user guides View all Konica Minolta AccurioPress C14000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

5 - Error Conditions, Problems and Solutions - Message List Message Information Reference JAM IN STACKER AREA There is a paper jam at the outfeed of the machine. Remove the jammed books and continue. JAM IN STITCHER AREA There is a paper jam in the stitch area. Open the folder cover, remove the paper jam and continue. See "Jam in the Stitch Area" on page 67. JAM IN STITCH HEAD There is a jam in the stitch head. See "Clear a Stitch Head Jam" on page 75. JAM IN TRIMMER There is a book jammed in the trimmer. Clear the jam and continue. See "Jam in the Trim Area" on page 70. MAIN CONTROL - No comms Use the mains ON/OFF switch. Turn the machine OFF, then turn the machine ON. If the problem continues, then call your service engineer. MANUALLY PARK SHUTTLE The shuttle is not parked correctly. Open the folder cover and move the shuttle to the park position. Close the folder cover. The shuttle will reset. When the message list is clear, continue operation. See "Manually park the Shuttle" on page 80. MISSING STITCHES The machine has detected missed stitches. Check if the stitch-wire is jammed or if the stitch-wire spool is empty. See "Clear a Stitch-wire Jam" on page 73 or see "Install New Stitchwire" on page 96. MOTOR CONTROLLER The drive motor controller is not NOT READY ready. If the problem continues, contact your service engineer. OPERATOR MAINTENANCE The machine needs routine main- See "Operator tenance by the operator. Maintenance" on page 83. REBOOT THE MACHINE Use the mains ON/OFF switch. Turn the machine OFF, then turn the machine ON. If the problem continues, then call your service engineer. REMOVE SET FROM FOLD AREA Open the folder cover and remove See "Jam in the the set. Folder or Former Area" on page 67. 60 Watkiss PowerSquare™224 User Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
5 - Error Conditions, Problems and Solutions - Message List
60
Watkiss PowerSquare™224 User Manual
JAM IN STACKER
AREA
There is a paper jam at the outfeed
of the machine. Remove the
jammed books and continue.
JAM IN STITCHER
AREA
There is a paper jam in the stitch
area. Open the folder cover,
remove the paper jam and con-
tinue.
See “Jam in the
Stitch Area” on
page 67.
JAM IN STITCH HEAD
There is a jam in the stitch head.
See “Clear a Stitch
Head Jam” on
page 75.
JAM IN TRIMMER
There is a book jammed in the
trimmer. Clear the jam and con-
tinue.
See “Jam in the
Trim Area” on
page 70.
MAIN CONTROL - No
comms
Use the mains ON/OFF switch.
Turn the machine OFF, then turn
the machine ON.
If the problem
continues, then call your service
engineer.
MANUALLY PARK
SHUTTLE
The shuttle is not parked correctly.
Open the folder cover and move
the shuttle to the park position.
Close the folder cover.
The shuttle
will reset.
When the message list
is clear, continue operation.
See “Manually
park the Shuttle”
on page 80.
MISSING STITCHES
The machine has detected missed
stitches.
Check if the stitch-wire is jammed
or if the stitch-wire spool is empty.
See “Clear a
Stitch-wire Jam”
on page 73 or see
“Install New Stitch-
wire” on page 96.
MOTOR CONTROLLER
NOT READY
The drive motor controller is not
ready. If the problem continues,
contact your service engineer.
OPERATOR MAINTE-
NANCE
The machine needs routine main-
tenance by the operator.
See “Operator
Maintenance” on
page 83.
REBOOT THE
MACHINE
Use the mains ON/OFF switch.
Turn the machine OFF, then turn
the machine ON.
If the problem
continues, then call your service
engineer.
REMOVE SET FROM
FOLD AREA
Open the folder cover and remove
the set.
See “Jam in the
Folder or Former
Area” on page 67.
Message
Information
Reference