Konica Minolta Kodak Scan Station 710 Administration Guide - Page 13

Pre-installation checklist, UNC names for folders, NETBIOS usage

Get Konica Minolta Kodak Scan Station 710 PDF manuals and user guides View all Konica Minolta Kodak Scan Station 710 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

UNC names for folders - you will need to know the fully qualified UNC name for each network folder that will be used by your Scan Station(s). When configuring network destinations, this will be the information entered into the Address field of the Add: Network Folder dialog box. For example, you could create a folder called "scanfolder" on a server called "acmeserver" that would be reserved for Scan Station access. You would reference it by the following UNC name: \\acmeserver\scanfolder. NETBIOS usage - in network environments that use routers it is common practice to block NETBIOS traffic on your router. You may need to know the IP address of the server where you want to scan documents. By substituting the IP address of the server instead of the NETBIOS computer name, you can bypass the network traffic restrictions that may cause network scanning to fail. For example, the previously defined network address: \\acmeserver\scanfolder should be replaced with something similar to: \\192.168.2.10\scanfolder. Pre-installation checklist It is recommended that you review this checklist before configuring the Kodak Scan Station 700. This information is needed to create the initial configuration file to complete the installation. Locate any information you are unsure of before creating the configuration file. See your system or network administrator if you have questions about this information. Device Settings/IP Address The following settings are found using the Scanner tab and by selecting Scanner>Add. Parameter Name Your Setting Chapter Reference Automatic (DHCP) See Chapter 9, "Adding a Scanner". IP Address Settings - Static Static (IPv4) IP Address Subnet Mask Default Gateway Preferred DNS Server Alternate DNS Server Preferred WINS Server Device Settings/Network Destination Credentials The following settings are found using the Configuration tab and by selecting Edit>Device Settings. Parameter Name Your Setting Chapter Reference Username, Password, Domain Remote Configuration Settings • See Chapter 9, "Best practices" for creating an account for your Scan Station. • See Chapter 4, "Configuring your device options". 2-2 A-61796 December 2013

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
2-2
A-61796
December 2013
UNC names for folders
— you will need to know the fully qualified
UNC name for each network folder that will be used by your Scan
Station(s). When configuring network destinations, this will be the
information entered into the
Address
field of the Add: Network Folder
dialog box. For example, you could create a folder called “
scanfolder
”
on a server called “
acmeserver
” that would be reserved for Scan
Station access. You would reference it by the following UNC name:
\\acmeserver\scanfolder
.
NETBIOS usage
— in network environments that use routers it is
common practice to block NETBIOS traffic on your router. You may
need to know the IP address of the server where you want to scan
documents. By substituting the IP address of the server instead of the
NETBIOS computer name, you can bypass the network traffic
restrictions that may cause network scanning to fail. For example, the
previously defined network address:
\\acmeserver\scanfolder
should be
replaced with something similar to:
\\192.168.2.10\scanfolder
.
Pre-installation
checklist
It is recommended that you review this checklist
before
configuring the
Kodak
Scan Station 700. This information is needed to create the initial
configuration file to complete the installation. Locate any information
you are unsure of before creating the configuration file. See your
system or network administrator if you have questions about this
information.
Device Settings/IP Address
The following settings are found using the Scanner tab and by selecting
Scanner>Add
.
Parameter Name
Your Setting
Chapter Reference
Automatic (DHCP)
See Chapter 9, “Adding a Scanner”.
IP Address Settings — Static
Static (IPv4)
IP Address
Subnet Mask
Default Gateway
Preferred DNS Server
Alternate DNS Server
Preferred WINS Server
Device Settings/Network Destination Credentials
The following settings are found using the Configuration tab and by selecting
Edit>Device Settings
.
Parameter Name
Your Setting
Chapter Reference
Username, Password, Domain
• See Chapter 9, “Best practices” for
creating an account for your Scan
Station.
• See Chapter 4, “Configuring your
device options”.
Remote Configuration Settings