Kyocera FS 2000D FS-2000D/3900DN/4000DN Operation Guide Rev-1.2 (Advanced Edit - Page 16

Envelopes, Thick Paper, Colored Paper, Preprinted Paper

Get Kyocera FS 2000D - B/W Laser Printer PDF manuals and user guides View all Kyocera FS 2000D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Handling Paper 1-10 Envelopes Envelopes should be fed in the face-up position, right edge first. Since the composition of an envelope is more complex than that of ordinary paper, it is not always possible to ensure consistent printing quality over the entire envelope surface. Normally, envelopes have a diagonal grain direction. Refer to Paper Grain on page 1-6. This direction can easily cause wrinkles and creases when envelopes pass through the printer. Before purchasing envelopes, make a test print to check whether the printer accepts the envelope. • Do not use envelopes that have an encapsulated liquid adhesive. • Avoid a long printing session for envelopes only. Extended envelope printing can cause premature printer wear. • If jams occur, try setting a lesser number of envelopes on the MP tray. • To avoid jams caused by curled envelopes, stack no more than 10 printed envelopes on the output tray. Thick Paper Fan the stack of paper and align the edges before loading them in the MP tray. Some types of paper have rough edges on the back (those are created when the paper is cut). In this case, put the paper on a flat place and rub the edges once or twice with, for example, a ruler to smooth them. Feeding rough edged paper may cause paper jams. NOTE: If the paper jams even after you smooth it out, load the paper in the MP Tray with the leading edge raised up a few millimeters as shown in the illustration. Colored Paper Colored paper should satisfy the same conditions as white bond paper, refer to Paper Specifications, on page 1-2. In addition, the pigments used in the paper must be able to withstand the heat of fusing during the printing process (up to 200°C or 392°F). Preprinted Paper Preprinted paper should satisfy the same conditions as white bond paper, refer to Paper Specifications, on page 1-2.The preprinted ink must be able ADVANCED OPERATION GUIDE

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
Handling Paper
1-10
ADVANCED OPERATION GUIDE
Envelopes
Envelopes should be fed in the face-up
position, right edge first.
Since the composition of an envelope is
more complex than that of ordinary
paper, it is not always possible to ensure
consistent printing quality over the entire
envelope surface.
Normally, envelopes have a diagonal
grain direction. Refer to
Paper Grain on
page 1-6
. This direction can easily cause wrinkles and creases when
envelopes pass through the printer. Before purchasing envelopes, make a
test print to check whether the printer accepts the envelope.
•
Do not use envelopes that have an encapsulated liquid adhesive.
•
Avoid a long printing session for envelopes only. Extended envelope
printing can cause premature printer wear.
•
If jams occur, try setting a lesser number of envelopes on the MP tray.
•
To avoid jams caused by curled envelopes, stack no more than 10
printed envelopes on the output tray.
Thick Paper
Fan the stack of paper and align the edges before loading them in the MP
tray. Some types of paper have rough edges on the back (those are
created when the paper is cut). In this case, put the paper on a flat place
and rub the edges once or twice with, for example, a ruler to smooth them.
Feeding rough edged paper may cause paper jams.
NOTE:
If the paper jams even
after you smooth it out, load the
paper in the
MP Tray
with the
leading edge raised up a few
millimeters as shown in the
illustration.
Colored Paper
Colored paper should satisfy the same conditions as white bond paper,
refer to
Paper Specifications, on page 1-2.
In addition, the pigments used
in the paper must be able to withstand the heat of fusing during the printing
process (up to 200°C or 392°F).
Preprinted Paper
Preprinted paper should satisfy the same conditions as white bond paper,
refer to
Paper Specifications, on page 1-2.
The preprinted ink must be able