Kyocera TASKalfa Pro 15000c Pro 15000c Advanced Operation Guide - Page 117

Troubleshooting > Troubleshooting When Printing Image, Load SRA3/Ledger size paper.

Get Kyocera TASKalfa Pro 15000c PDF manuals and user guides View all Kyocera TASKalfa Pro 15000c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 117 highlights

Troubleshooting > Troubleshooting When Printing Image 3 If so, change the mode to [Quality] > [Start] > [Stop] key. NOTE If [Quality] is selected, printing will not start until the print head temperature is 26.1 ° C/ 78.98°F or higher. 4 If the mode is [Quality] and the problem is not solved, go to the next step. 7 Execute print head cleaning Discharge amount get small because of high viscosity ink. 1 Load SRA3/Ledger size paper. 2 [Home] key > [...] > [Professional Settings] > [U744 Head Cleaning] > [02 Check] A nozzle check pattern is printed. 3 Align the mark on the chart arrow with the mark on the upper left corner of the platen glass. As shown in the illustration, place the pattern on the glass platen with the printed side down and the edge with the arrows toward the back. NOTE The printed position of the arrows in the nozzle check pattern may be in from the edge, depending on the size of the pattern. Regardless of the position of the arrows, place the pattern in the upper left corner of the glass platen. 4 Select [Start]. After the pattern is scanned, the number of clogged nozzles of each color is displayed. If there is even one clogged nozzle, go to the next step. 5 [Stop] key > select [01 Cleaning]. 6 Select the color which has clogged nozzles > select [Strong] as the strength of cleaning > [Start] key. The head cleaning begins. 7 If the nozzle clog is not solved using head cleaning three times, change the strength of cleaning to [Ex Strong] and execute cleaning three times. 8 In case that no improvement is observed, then go to next step. 4-14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
4-14
Troubleshooting > Troubleshooting When Printing Image
3
If so, change the mode to [Quality] > [Start] > [Stop] key.
4
If the mode is [Quality] and the problem is not solved, go to the next step.
7
Execute print head cleaning
Discharge amount get small because of high viscosity ink.
1
Load SRA3/Ledger size paper.
2
[Home] key > [...] > [Professional Settings] > [U744 Head Cleaning] > [02 Check]
A nozzle check pattern is printed.
3
Align the mark on the chart arrow with the mark on the upper left corner of the platen glass.
As shown in the illustration, place the pattern on the glass platen with the printed side down
and the edge with the arrows toward the back.
4
Select [Start].
After the pattern is scanned, the number of clogged nozzles of each color is displayed.
If there is even one clogged nozzle, go to the next step.
5
[Stop] key > select [01 Cleaning].
6
Select the color which has clogged nozzles > select [Strong] as the strength of cleaning >
[Start] key.
The head cleaning begins.
7
If the nozzle clog is not solved using head cleaning three times, change the strength of
cleaning to [Ex Strong] and execute cleaning three times.
8
In case that no improvement is observed, then go to next step.
NOTE
If [Quality] is selected, printing will not start until the print head temperature is 26.1 ° C/
78.98°F or higher.
NOTE
The printed position of the arrows in the nozzle check pattern may be in from the edge,
depending on the size of the pattern. Regardless of the position of the arrows, place the
pattern in the upper left corner of the glass platen.