Kyocera TASKalfa Pro 15000c Pro 15000c Advanced Operation Guide - Page 169

List of Professional Settings

Get Kyocera TASKalfa Pro 15000c PDF manuals and user guides View all Kyocera TASKalfa Pro 15000c manuals
Add to My Manuals
Save this manual to your list of manuals

Page 169 highlights

Appendix > List of Professional Settings List of Professional Settings No. 000 023 034 059 208 246 251 327 407 460 468 700 730 731 733 Item Output Maintenance Report Reset Settings Adjust Paper Timing Data Set Fan Mode Set Deck Paper Size Adjust Finisher Clear Maintenance Counter Set Cassette Heater Control Adj. Write Timing(Reverse) Adjust Conveying Sensor Color Regist Adj. Data Head Information Set Head Cleaning Set Decurler Set Warm Up Mode 734 Set Paper Discharge Mode 735 Set Ink Temperature Control 736 Set Waste Paper 744 Set Head Cleaning 750 Set Head Coefficient 754 Adjust Discharge Width 755 Adjust Conveying CIS 760 Set Color Bleeding 917 Read/Write Backup Data Description Print maintenance reports and status pages. The adjustment setting value is restored to the factory default. Adjust the tip edge timing and center line of paper. Adjust the air flow of the drying conveyance fan motor according to the paper type. Configure the paper size to be loaded in cassettes 3 and 4. Adjust various setting values when using a 4,000-sheet finisher, Inverter and Decurler Unit, and 5,000-sheet stacker. Clear the counter value after replacing parts when the print image reached 600,000. Switch the control mode of optional cassette heater integrated in the machine. Adjust the writing timing of the back surface image drawing position at duplex copying. Adjust the double feed sensor threshold of the machine's conveying sensor. Adjust the print head position of each color or the color drift. Displays the print head temperature. Configure the purge strength and execution interval of head cleaning. Adjust the fan control of the decurl unit for the machine and the Inverter Decurler Unit (DE-9100). Configure the print head protection or the heater operation control of the Inverter and Decurler Unit (DE-9100), during warmup operation. Set whether to enable the discharge mode or print the wasted paper. Adjust the printable ink temperature at Print Priority setting. Specify the timing of ink discharge. Perform a stronger level of head cleaning than the settings in the system menu to eliminate print head failure. Fine-tune the image density by adjusting the print head drive voltage. Adjust the width alignment cursor position to the paper width. Perform CIS position correction (center and side). Adjust the gap between colors when blur or void occurs in the color boundaries. Back up (export) the user Paper Catalog configured in the machine and import it for use in another machine. 5-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
5-2
Appendix > List of Professional Settings
List of Professional Settings
No.
Item
Description
000
Output Maintenance Report
Print maintenance reports and status pages.
023
Reset Settings
The adjustment setting value is restored to the factory default.
034
Adjust Paper Timing Data
Adjust the tip edge timing and center line of paper.
059
Set Fan Mode
Adjust the air flow of the drying conveyance fan motor according
to the paper type.
208
Set Deck Paper Size
Configure the paper size to be loaded in cassettes 3 and 4.
246
Adjust Finisher
Adjust various setting values when using a 4,000-sheet finisher,
Inverter and Decurler Unit, and 5,000-sheet stacker.
251
Clear Maintenance Counter
Clear the counter value after replacing parts when the print image
reached 600,000.
327
Set Cassette Heater Control
Switch the control mode of optional cassette heater integrated in
the machine.
407
Adj. Write Timing(Reverse)
Adjust the writing timing of the back surface image drawing
position at duplex copying.
460
Adjust Conveying Sensor
Adjust the double feed sensor threshold of the machine's
conveying sensor.
468
Color Regist Adj. Data
Adjust the print head position of each color or the color drift.
700
Head Information
Displays the print head temperature.
730
Set Head Cleaning
Configure the purge strength and execution interval of head
cleaning.
731
Set Decurler
Adjust the fan control of the decurl unit for the machine and the
Inverter Decurler Unit (DE-9100).
733
Set Warm Up Mode
Configure the print head protection or the heater operation
control of the Inverter and Decurler Unit (DE-9100), during warm-
up operation.
734
Set Paper Discharge Mode
Set whether to enable the discharge mode or print the wasted
paper.
735
Set Ink Temperature Control
Adjust the printable ink temperature at Print Priority setting.
736
Set Waste Paper
Specify the timing of ink discharge.
744
Set Head Cleaning
Perform a stronger level of head cleaning than the settings in the
system menu to eliminate print head failure.
750
Set Head Coefficient
Fine-tune the image density by adjusting the print head drive
voltage.
754
Adjust Discharge Width
Adjust the width alignment cursor position to the paper width.
755
Adjust Conveying CIS
Perform CIS position correction (center and side).
760
Set Color Bleeding
Adjust the gap between colors when blur or void occurs in the
color boundaries.
917
Read/Write Backup Data
Back up (export) the user Paper Catalog configured in the
machine and import it for use in another machine.