Kyocera TASKalfa Pro 15000c Pro 15000c Advanced Operation Guide - Page 133

Void area at the leading edge, Con print head cleaning operation according to paper, width

Page 133 highlights

Troubleshooting > Troubleshooting When Printing Image *3 When Void area at the leading edge is observed, configure the settings of U736 as below. In case of temperature is normal or high: U736 >Ink discharge > Job start and Specific Interval > Mode4 (800) In case of temperature is low: U736 >Ink discharge > Job start and Specific Interval > Mode2 (160) *4 If the faint image at the leading edge section occurs right after executing the setting 6, set U734 to [Off], and configure the settings of U736 as below. U736 > Ink discharge > Job start and Specific interval > Mode2 (160) NOTE Settings are set by the environment showed in the chart below. Humi Low Temperature Normal Temperature High Temperature Temp When selecting [04 All], waste paper is printed every job printout. 5 [Start] key > [Stop] key > [Close] The settings are configured and the screen returns to Professional settings menu. 6 In case that no improvement is observed, contact our service representative. Void area at the leading edge HH Bad Good The ink in the nozzles that have not been discharged for a while has become transparent due to material separation caused by evaporation of moisture, etc. 1 Configure print head cleaning operation according to paper width Use this setting when there is any void area at the leading edge of the paper after changing to a print job with a different paper width. 1 [Home] key > [...] > [Professional Settings] > [U730 Set Head Cleaning] > [03 Purge(Width)] 4-30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177

4-30
Troubleshooting > Troubleshooting When Printing Image
When selecting [04 All], waste paper is printed every job printout.
5
[Start] key > [Stop] key > [Close]
The settings are configured and the screen returns to Professional settings menu.
6
In case that no improvement is observed, contact our service representative.
Void area at the leading edge
The ink in the nozzles that have not been discharged for a while has become transparent due to material separation
caused by evaporation of moisture, etc.
1
Configure print head cleaning operation according to paper
width
Use this setting when there is any void area at the leading edge of the paper after changing to
a print job with a different paper width.
1
[Home] key > [...] > [Professional Settings] > [U730 Set Head Cleaning] > [03
Purge(Width)]
*3
When Void area at the leading edge is observed, configure the settings of U736 as
below.
In case of temperature is normal or high:
U736 >Ink discharge > Job start and Specific Interval > Mode4 (800)
In case of temperature is low:
U736 >Ink discharge > Job start and Specific Interval > Mode2 (160)
*4
If the faint image at the leading edge section occurs right after executing the setting 6,
set U734 to [Off], and configure the settings of U736 as below.
U736 > Ink discharge > Job start and Specific interval > Mode2 (160)
NOTE
Settings are set by the environment showed in the chart below.
Temp
Humi
High Temperature
Normal Temperature
Low
Temperature
Bad
Good
H
H