Samsung SRP-275CEPG Operation Manual

Samsung SRP-275CEPG - Bixolon Two-color Dot-matrix Printer Manual

Get Samsung SRP-275CEPG - Bixolon Two-color Dot-matrix Printer PDF manuals and user guides View all Samsung SRP-275CEPG manuals
Add to My Manuals
Save this manual to your list of manuals

Samsung SRP-275CEPG manual content summary:

  • Samsung SRP-275CEPG | Operation Manual - Page 1
    ELECTRO - MECHANICS Operator's manual POS impact dot matrix printer SRP-275 printed in korea 2004. 09 ELECTRO - MECHANICS
  • Samsung SRP-275CEPG | Operation Manual - Page 2
    In using the present appliance, please keep the following safety regulations in order to prevent any hazard or material damage. WARNING Violating following instructions can cause serious injury or death. Do not plug several products in one multi-outlet. This can provoke over-heating and a fire. If
  • Samsung SRP-275CEPG | Operation Manual - Page 3
    your dealer when you need these services. DISASSEMBLING PROHIBITED PRINTER Do not dealer. TO UNPLUG PROHIBITED SRP-275 All rights reserved. No part SAMSUNG ELECTRO-MECHANICS s operating and maintenance instructions. SAMSUNG ELECTRO-MECHANICS shall not be liable against any damages or problems
  • Samsung SRP-275CEPG | Operation Manual - Page 4
    replacing the paper roll 1.6. Changing the frame control paper position 1.7. Installing wall mount 1.8. Using the operation panel 1.9. Self test Chapter 2. Troubleshooting commands 5.3.3 settings outside the defined range 5.4 Commands for SRP-275 Series 5.4.1 Commands list for Epson mode (TM-U220)
  • Samsung SRP-275CEPG | Operation Manual - Page 5
    Introduction The SRP-275 is a high-quality impact dot matrix POS printer. This one-station near end switch is standard. A internal AC adaptor. Please be sure to read the instructions in this manual carefully before using your new printer. Front View Rear View 1 CHAPTER CONTENTS SETTING UP THE
  • Samsung SRP-275CEPG | Operation Manual - Page 6
    shown in the illustration below. If any items are damaged or missing, please contact your dealer. SRP-275 A , C AC adaptor Power cord Ribbon Cassette Paper roll Quick reference sheet Operator's manual 1.2 Choosing a place for the printer Avoid locations that are subject to direct sunlight or
  • Samsung SRP-275CEPG | Operation Manual - Page 7
    , turn the knob clockwise again to make sure the ribbon moves freely in the cassette. 6) Close front cover of printer. Malfunctions and other problems may arise if other than specified ribbon cassettes are used in the printer. The Warranty may be void if other than specified ribbon cassettes are
  • Samsung SRP-275CEPG | Operation Manual - Page 8
    tighten two screws(3 x 6) to reattach.) 4) Close the rear cover. 5) Change the Memory Switch setting for changing paper roll width. (See the instructions "Setting the Memory Switches"(3.1) in Chapter 3.) 1.8 Installing wall mount (Option) 1) Turn the Set over and attach the Bracket hanger to the
  • Samsung SRP-275CEPG | Operation Manual - Page 9
    service person. - PAPER OUT LED (Red Color) When this indicator light is on, it means that the paper near end. Replace the instructions "Self test" (1.7) in this chapter for self test.) (See the instructions "Hexadecimal you have any trouble. If the self test works correctly, the problem is in the
  • Samsung SRP-275CEPG | Operation Manual - Page 10
    Note 1-8 2 CHAPTER TROUBLESHOOTING 2.1 ERROR LED blinking pattern 2-2 2.2 The printer does not start printing 2-3 2.3 The printer stops printing 2-4 2.4 You want to check the operation of the printer by itself 2-4 2.5
  • Samsung SRP-275CEPG | Operation Manual - Page 11
    Troubleshooting This chapter gives solutions to some printer problems light is still blinking, call your supervisor or a service person. 2.2 The printer does not start printing "Installing paper roll" (1.5) in Chapter 1 for instructions on installing or replacing the paper roll. - If the ERROR LED
  • Samsung SRP-275CEPG | Operation Manual - Page 12
    CHAPTER 2 Troubleshooting 2.3 The printer stops printing If the ERROR LED is on (but not blinking), the printer is off line. Check to see that the covers are closed and check the paper state. See "Installing paper roll"(1.5) in Chapter 1 for instructions on installing or replacing the paper roll. If
  • Samsung SRP-275CEPG | Operation Manual - Page 13
    Note 3 CHAPTER CONTENTS SWITCH SETTINGS 3.1 Setting the DIP Switches 3-2 3.1.1 DIP Switch Setting for Epson(ESC/POS) mode 3-2 3.1.2 DIP Switch setting for Citizen(iDP 3550) mode 3-3 3.1.3 DIP Switch setting for Star(SP500) mode 3-4 3.2 Setting the Memory Switches 3-5 3.2.1 Memory
  • Samsung SRP-275CEPG | Operation Manual - Page 14
    CHAPTER 3 Switch settings Although the factory settings are best for almost all users, if you have special requirements, you can change the DIP Switch. 3.1 Setting the DIP Switches Your printer has two sets of DIP Switches. The functions of the switches are shown in the following table. 3.1.1 DIP
  • Samsung SRP-275CEPG | Operation Manual - Page 15
    CHAPTER 3 Switch settings DIP Switch 2 (RS232C serial interface model) Switch Function 2-1 Word length 2-2 Parity check 2-3 Parity selection 2-4 Handshaking 2-5 2-6 Baud rate selection(*3) 2-7 Near end Switch 2-8 Mechanism type ON 8 bits Disable ODD DTR/DSR OFF 7 bits Enable EVEN
  • Samsung SRP-275CEPG | Operation Manual - Page 16
    are stored in the NV memory; therefore, even if the printer is turned off, the settings are maintained. When you replace a SRP-270 with a SRP-275, you should adjust the MSW8-5 to OFF. Memory Switch 2 Switch Function 1 Reserved 2 Reserved 3 Reserved for Chinese selection 4~8 Code page
  • Samsung SRP-275CEPG | Operation Manual - Page 17
    is changed every time the rear cover is open or closed. When you replace a SRP270 with a SRP-275, you should adjust the MSW 8-5 to Off. MSW 8-8 : When Off the enabled settings of the memory switches and instructions. 5) Follow the instructions to process the switch setup. In the Memory Switch setup,
  • Samsung SRP-275CEPG | Operation Manual - Page 18
    CHAPTER 3 Switch settings Procedure of Memory Switch setting 3-10 3.2.2 Memory Switch setting for Star (SP500) mode Settings Memory Switches are from MSW 0 to 8 MSW 8. They are stored in non-volatile memory (flash memory). To change the settings, send the following commands from the host. [Name
  • Samsung SRP-275CEPG | Operation Manual - Page 19
    CHAPTER 3 Switch settings Default Settings The default settings for Memory Switch 0 to Memory Switch 8 are shown below. Settings vary for single byte character countries (standard specifications (SBCS)) and for double-byte character countries (Chinese character specifications (DBCS)). Standard
  • Samsung SRP-275CEPG | Operation Manual - Page 20
    for selecting Option 2 and Option 3. 1)Do not apply an upper line or an underline to characters when rotating 90 or 270 degrees. 3-14 Memory Switch 1 Bit Function F Reserved E~5 4 Zero style 3~0 International Characters(*1) 0 1 Normal Slash zero Refer to the following table
  • Samsung SRP-275CEPG | Operation Manual - Page 21
    CHAPTER 3 Switch settings Memory Switch 2 Bit Function F Reserved E How to recover to print ready after Inserting paper D~C Reserved B Printing region width(*1) A Paper width selection(*1) 9~4 3 Contextual auto-cut function (*2) 2 1~0 Near end switch function(*3) 0 Press FEED 1
  • Samsung SRP-275CEPG | Operation Manual - Page 22
    . Then take off the DIP Switch cover, which is shown in the illustration below. 3) Set the switches using a pointed tool, such as tweezers or a small. 4) Replace the DIP Switch cover. Then secure it with the screw. The new settings take effect when you turn on the printer. 3-18 3-19
  • Samsung SRP-275CEPG | Operation Manual - Page 23
    Note 3-20 4 CHAPTER CONTENTS CODE TABLE 4.1 Page 0 (PC437 : USA, Standard Europe (International Character Set : USA)) 4-2 4.2 Page 1 (Katakana) 4-3 4.3 Page 2 (PC850 : Multilingual) 4-4 4.4 Page 3 (PC860 : Portuguese) 4-5 4.5 Page 4 (PC863 : Canadian-French) 4-6 4.6 Page 5 (PC865 :
  • Samsung SRP-275CEPG | Operation Manual - Page 24
    CHAPTER 4 Code table The following pages show the character code tables. To fine the character corresponding to a hexadecimal number, count across the top of the table for the left digit and count down the left column of the table right digit. For example, 4A=J 4.1 Page 0 (PC 437 : USA, Standard
  • Samsung SRP-275CEPG | Operation Manual - Page 25
    CHAPTER 4 Code table 4.3 Page 2 (PC850 : Multilingual) 4.4 Page 3 (PC860 : Portuguese) 4-4 4-5
  • Samsung SRP-275CEPG | Operation Manual - Page 26
    CHAPTER 4 Code table 4.5 Page 4 (PC863 : Canadian-French) 4.6 Page 5 (PC865 : Nordic) 4-6 4-7
  • Samsung SRP-275CEPG | Operation Manual - Page 27
    CHAPTER 4 Code table 4.7 Page 16 (WPC1252 : Latin1) 4.8 Page 17 (PC866 : Russian) 4-8 4-9
  • Samsung SRP-275CEPG | Operation Manual - Page 28
    CHAPTER 4 Code table 4.9 Page 18 (PC852 : DosLatin2) 4.10 Page 19 (PC858 : Euro) 4-10 4-11
  • Samsung SRP-275CEPG | Operation Manual - Page 29
    CHAPTER 4 Code table 4.11 Page 21 (PC862 : Israel) 4.12 Page 22 (PC864 : Arabic) 4-12 4-13
  • Samsung SRP-275CEPG | Operation Manual - Page 30
    CHAPTER 4 Code table 4.13 Page 23 (Thai character code 42) 4.14 Page 24 (WPC1253 : Greek) 4-14 4-15
  • Samsung SRP-275CEPG | Operation Manual - Page 31
    CHAPTER 4 Code table 4.15 Page 25 (WPC1254 : Turkish) 4.16 Page 26 (WPC1257 : Baltic) 4-16 4-17
  • Samsung SRP-275CEPG | Operation Manual - Page 32
    CHAPTER 4 Code table 4.17 Page 27 (Farsi) 4.18 Page 28 (WPC1251 : Russian) 4-18 4-19
  • Samsung SRP-275CEPG | Operation Manual - Page 33
    CHAPTER 4 Code table 4.19 Page 29 (PC737 : Greek) 4.20 Page 30 (PC775 : Baltic) 4-20 4-21
  • Samsung SRP-275CEPG | Operation Manual - Page 34
    CHAPTER 4 Code table 4.21 International character code table 4-22
  • Samsung SRP-275CEPG | Operation Manual - Page 35
    Notation 5.2 Explanation of Terms 5.3 Explanation Processing 5.3.1 Undefined codes 5.3.2 Undefined commands 5.3.3 settings outside the defined range 5.4 Commands for SRP-275 Series 5.4.1 Commands list for Epson mode (TM-U220) 5.4.2 Commands description for Epson mode (TM-U220) 5.4.3 Commands list
  • Samsung SRP-275CEPG | Operation Manual - Page 36
    CHAPTER 5 CONTROL COMMANDS LIST 5.1 Command notation XXXX [Name] The name of the command. [Format] The code sequence. [Range] Gives the allowable ranges for the arguments. [Description] Describes the command's function. [Notes] Provides important information on setting and using the printer command,
  • Samsung SRP-275CEPG | Operation Manual - Page 37
    CHAPTER 5 CONTROL COMMANDS LIST 5.4 Commands for SRP-275 Series 5.4.1 Commands list for EPSON Mode(TM-U220) n Command Description 1 HT Horizontal tab 2 LF Print and line feed 3 CR Print and carriage return 4 DLE EOT
  • Samsung SRP-275CEPG | Operation Manual - Page 38
    CHAPTER 5 CONTROL COMMANDS LIST 5.4.2 Commands description for Epson mode (TM-U220) HT [Name] Horizontal tab [Format] ASCII HT Hex 09 Decimal 9 [Range] None [Default] None [Description] Moves the printing position to the next horizontal tab. [Notes] This command is ignored unless
  • Samsung SRP-275CEPG | Operation Manual - Page 39
    CHAPTER 5 CONTROL COMMANDS LIST DLE EOT [Name] Real-time status transmission [Format] ASCII DLE Hex 10 EOT n 04 n [Range] [Description] Decimal 16 4 n 1 ≤n ≤4 Transmits 1 byte of status data specified in real time, using n as follows: n Function 1 Transmit printer status 2
  • Samsung SRP-275CEPG | Operation Manual - Page 40
    CHAPTER 5 CONTROL COMMANDS LIST Error status (n = 3) is as follows: Bit Binary Hex Decimal Status 0 0 00 0 Not used. Fixed to Off 1 1 02 2 Not used. Fixed to On 2 0 00 0 No mechanical error 1 04 4 Mechanical error occurred 3 0 00 0 No auto cutter error 1 08 8 Auto
  • Samsung SRP-275CEPG | Operation Manual - Page 41
    CHAPTER 5 CONTROL COMMANDS LIST DLE DC4 (fn = 1) [Name] Generate pulse at real-time [Format] ASCII DLE DC4 n m t Hex 10 14 n m t Decimal 16 20 n m t [Range] n = 1 m = 0, 1 1≤t≤8 [Description] Outputs the pulse specified by t to connector pin m as follows in real time: m
  • Samsung SRP-275CEPG | Operation Manual - Page 42
    CHAPTER 5 CONTROL COMMANDS LIST [Notes] - Functions for each bit can also be executed by the following commands: - Bit 0 (character font): ESC M - Bit 3 (Emphasized mode): ESC E - Bit 7 (underline mode): ESC - When some characters in a line are double-height, all characters on the line are aligned
  • Samsung SRP-275CEPG | Operation Manual - Page 43
    CHAPTER 5 CONTROL COMMANDS LIST ESC * [Name] Select bit-image mode [Format] ASCII ESC * m nL nH d1 ... dk Hex 1B 2A m nL nH d1 ... dk Decimal 27 42 m nL nH d1 ... dk [Range] m = 0, 1 0 ≤ nL ≤ 255 0 ≤ nH ≤ 3 0 ≤ d ≤ 255 k = nL + nHx255 [Default] None [Description] Selects
  • Samsung SRP-275CEPG | Operation Manual - Page 44
    CHAPTER 5 CONTROL COMMANDS LIST ESC 2 [Name] Select default line spacing [Format] ASCII ESC 2 Hex 1B 32 Decimal 27 50 [Range] None [Default] None [Description] Sets the line spacing to the "default line spacing." [Notes] - The default line spacing is about 4.23 mm (1/6 inch),
  • Samsung SRP-275CEPG | Operation Manual - Page 45
    CHAPTER 5 CONTROL COMMANDS LIST ESC ? [Name] Cancel user-defined characters [Format] ASCII ESC ? n Hex 1B 3F n Decimal 27 63 n [Range] 32 ≤ n ≤ 126 [Default] None [Description] Cancels the user-defined characters defined for the character code n. [Notes] After the user-defined
  • Samsung SRP-275CEPG | Operation Manual - Page 46
    CHAPTER 5 CONTROL COMMANDS LIST ESC E [Name] Turn emphasized mode on/off [Format] ASCII ESC E n Hex 1B 45 n Decimal 27 69 n [Range] 0 ≤ n ≤ 255 [Default] n = 0 [Description] Turns emphasized mode on or off. - When the LSB of n is 0, emphasized mode is turned off. - When the LSB
  • Samsung SRP-275CEPG | Operation Manual - Page 47
    CHAPTER 5 CONTROL COMMANDS LIST ESC M [Name] Select character font [Format] ASCII ESC Hex 1B M n 4D n Decimal 27 77 n [Range] [Default] n = 0, 1, 48, 49 n = 1 [Description] Selects a character font, using n as follows : n Font 0, 48 Font A(9 x 9) 1, 49 Font B(7 x 9) [Notes]
  • Samsung SRP-275CEPG | Operation Manual - Page 48
    feeding the paper. The printer goes offline and Paper LED comes on after printing stops. To resume printing, cancel the "paper near end" status by replacing the paper roll. If the roll paper near-end sensor is disabled and a paper near-end is detected, printing does not stop and the printer
  • Samsung SRP-275CEPG | Operation Manual - Page 49
    are disabled, the function of the panel button, such as feeding, will be executed when the panel button is turned on. To prevent problems caused by accidentally pressing the buttons, use this command to disable the buttons. ESC d [Name] Print and feed n lines [Format] ASCII ESC d n Hex
  • Samsung SRP-275CEPG | Operation Manual - Page 50
    255 Start macro definition (Define logo) - k = the number of total macro index - (256 x nH) + nL = the Length of each macro - m = (256 x nH) + nL The SRP-275 Printer maintains a 2M bit (256KB) section of flash memory to save NV bit image. This command is useful to define NV bit image (Logo). The
  • Samsung SRP-275CEPG | Operation Manual - Page 51
    CHAPTER 5 CONTROL COMMANDS LIST ESC r [Name] Select print color [Format] ASCII ESC r n Hex 1B 72 n Decimal 27 114 n [Range] n = 0, 1, 48, 49 [Default] n = 0 [Description] Selects a print color, using n as follows: n Selected color 0, 48 Black 1, 49 Red [Notes] This
  • Samsung SRP-275CEPG | Operation Manual - Page 52
    CHAPTER 5 CONTROL COMMANDS LIST ESC u [Name] [Format] [Range] [Default] [Notes] Transmit peripheral device status. ASCII ESC u n Hex 1B 75 n Decimal 27 117 n n = 0, 48 Transmit the peripheral device status of 1 byte. The peripheral device to be transmitted is as follows: Bit Binary
  • Samsung SRP-275CEPG | Operation Manual - Page 53
    CHAPTER 5 CONTROL COMMANDS LIST ESC [Name] [Format] [Range] [Default] [Description] [Notes] Turn upside-down printing mode on/off. ASCII ESC { n Hex 1B 7B n Decimal 27 123 n 1 ≤ n ≤ 255 n = 0 Turn upside-down printing mode on or off. -When the LSB of n is 0, upside-down printing
  • Samsung SRP-275CEPG | Operation Manual - Page 54
    CHAPTER 5 CONTROL COMMANDS LIST The modes selectable by m are as follows : "Vertical" is in the direction of paper feeding and "horizontal" is perpendicular (at right angles) to the direction of paper feeding. The maximum number of dots for printing depends on the setting of DIP Switch [DSW1-8] and
  • Samsung SRP-275CEPG | Operation Manual - Page 55
    CHAPTER 5 CONTROL COMMANDS LIST GS ( A [Name] Execute test print [Format] ASCII GS ( A pL pH n m Hex 1D 28 41 02 00 n m Decimal 29 40 65 2 0 n m [Range] 1 ≤ m ≤ 3, 49 ≤ m ≤ 3 [Description] Executes a specified test print. - pL and pH specify the number of parameters following n to
  • Samsung SRP-275CEPG | Operation Manual - Page 56
    an index of note for the following: - Customize information: index of the NV bit image definition contents. - Maintenance information: ink ribbon replacement date, telephone number of company, etc. [Notes for transmitting processing of the block data] - Data is send by Function 2, 3, 4, or 5. When
  • Samsung SRP-275CEPG | Operation Manual - Page 57
    CHAPTER 5 CONTROL COMMANDS LIST GS ( C pL pH m fn b c1 c2 [Format] ASCII GS ( C pL pH m fn b c1 c2 Hex 1D 28 43 05 00 00 fn 00 c1 c2 Decimal 29 40 67 5 0 0 fn 0 c1 c2 [Range] (pL + pHx256) = 5 (pL = 5, pH = 0) m = 0 fn = 0, 48 b = 0 32 ≤ c1 ≤ 126 32 ≤ c2 ≤ 126 [
  • Samsung SRP-275CEPG | Operation Manual - Page 58
    CHAPTER 5 CONTROL COMMANDS LIST [Notes] - When the specified record exists, the printer sends the "Header to NUL" data shown below: Send data Header Identifier Identification status (*1) (*2) Data (*3) NUL Hex 37H 70H 40H or 41H 20H __FEH 00H Decimal 55 112 64 or 65 32 __254 0 Data quantity 1
  • Samsung SRP-275CEPG | Operation Manual - Page 59
    CHAPTER 5 CONTROL COMMANDS LIST GS ( C pL pH m fn b [Format] [Range] [Description] [Notes] ASCII GS ( C pL pH m fn b Hex 1D 28 43 03 00 00 fn 00 Decimal 29 40 67 3 0 0 fn 0 (pL + pHx 256) = 3 (pL = 3, pH = 0) m = 0 fn = 4, 52 b = 0 The printer sends the available NV user
  • Samsung SRP-275CEPG | Operation Manual - Page 60
    CHAPTER 5 CONTROL COMMANDS LIST - See [Notes for transmission process] for description of transmission process. - See [Notes for ESC/POS Handshaking Protocol] for description of ESC/POS Handshaking Protocol. GS ( C pL pH m fn b d1 d2 d3 [Format] ASCII GS ( C pL pH m fn b d1 d2 d3
  • Samsung SRP-275CEPG | Operation Manual - Page 61
    CHAPTER 5 CONTROL COMMANDS LIST GS ( E [Name] User setup commands [Format] ASCII GS ( E pL pH fn [parameters] Hex 1D 28 45 pL pH fn [parameters] Decimal 29 40 69 pL pH fn [parameters] [Description] Controls the user setting modes. The table below explains the functions available in this
  • Samsung SRP-275CEPG | Operation Manual - Page 62
    CHAPTER 5 CONTROL COMMANDS LIST GS ( E pL pH fn d1 d2 [Format] ASCII GS ( E pL pH fn d1 d2 Hex 1D 28 45 03 00 01 49 4E Decimal 29 40 69 3 0 1 73 78 [Range] (pL + pH x 256) = 3 (pL = 3, pH = 0) fn = 1 d1 = 73 d2 = 78 [Description] This command changes the printer into the user
  • Samsung SRP-275CEPG | Operation Manual - Page 63
    CHAPTER 5 CONTROL COMMANDS LIST GS ( E pL pH fn [a1 b18...b11]...[ak nk8 nk1] [Format] ASCI G ( E pL pH fn [a1 b18...b11 ]...[ak nk8 nk1] Hex 1D 28 45 pL pH 03 [a1 b18...b11]...[ak nk8 nk1] Decimal 29 40 69 pL pH 3 [a1 b18...b11]...[ak nk8 nk1] [Range] a = 2, 8 [Default] all
  • Samsung SRP-275CEPG | Operation Manual - Page 64
    CHAPTER 5 CONTROL COMMANDS LIST GS ( E pL pH fn [a1 n1L n1H]...[ak nkL nkH] [Format] [Range] [Default] [Description] ASCII GS ( E pL pH fn [a1n1L n1H] ... [ak nkL nkH] Hex 1D 28 45 pL pH 05 [a1 n1L n1H] ... [ak nkL nkH] Decimal 29 40 69 pL pH 5 [a1 n1L n1H] ... [ak nkL nkH] 4 ≤ (
  • Samsung SRP-275CEPG | Operation Manual - Page 65
    CHAPTER 5 CONTROL COMMANDS LIST GS ( E pL pH fn a d1...dk [Format] ASCII GS ( E pL pH fn a d1...dk Hex 1D 28 45 pL pH 0B a d1...dk Decimal 29 40 69 pL pH 11 a d1...dk [Range] 3 ≤ ( pL + pH x 256) ≤ 8 (3 ≤ pL ≤ 8, 0 ≤ pH ≤ 255) n = 11 1 ≤a ≤4 48 ≤ d ≤ 57 [a = 1] 48 ≤ d ≤ 50 [a =
  • Samsung SRP-275CEPG | Operation Manual - Page 66
    version Transmits printer information A (common information), using n as follows: n Printer ID Specification 33 Type information Supported functions Transmits printer information B (common information), using n as follows: n Printer ID Specification 65 Firmware version Firmware
  • Samsung SRP-275CEPG | Operation Manual - Page 67
    Off 00 1 On 02 2 Off 00 On 04 3-5 - - 6 On 40 7 Off 00 0 Multi-byte character codes are not supported. 1 Multi-byte character codes are supported. 0 Auto cutter not installed. 2 Auto cutter installed. 0 DM-D (customer display) is not installed. 4 DM-D (customer display) is installed
  • Samsung SRP-275CEPG | Operation Manual - Page 68
    cutter is installed/not installed] indicates the state of DIP switch 1-3. Bit 2: The bit [DM-D (Customer display) isn't supported. Printer model (n = 67) Printer model: SRP-275 Type information (n = 33) Bit 1: [Auto cutter is installed/not installed] indicates the state of DIP switch 1-3. Bit 2: The
  • Samsung SRP-275CEPG | Operation Manual - Page 69
    CHAPTER 5 CONTROL COMMANDS LIST GS a [Name] Enable/disable Automatic Status Back (ASB) [Format] ASCII GS a n Hex 1D 61 n Decimal 29 97 n [Range] [Default] 0 ≤ n ≤ 255 When DIP Switch or Memory Switch (BUSY condition) is Off: n = 0 When DIP Switch or Memory Switch (BUSY condition) is On: n =
  • Samsung SRP-275CEPG | Operation Manual - Page 70
    CHAPTER 5 CONTROL COMMANDS LIST [Note] Only if ESC 4 is selected or paper stop printing sensor is not selected. Basic ASB status is 4-byte configuration [first byte - fourth byte]. The status to be transmitted are as follows: First byte (printer information) Bit Off/On Hex Decimal Function 0
  • Samsung SRP-275CEPG | Operation Manual - Page 71
    CHAPTER 5 CONTROL COMMANDS LIST GS r [Name] Transmit status [Format] ASCII GS r n Hex 1D 72 n Decimal 29 114 n [Range] n = 1, 2, 49, 50 [Description] Transmits 1 byte of status data using n as follows: [Notes] n Function 1, 49 Transmits paper sensor status 2, 50 Transmits drawer kick-
  • Samsung SRP-275CEPG | Operation Manual - Page 72
    width for external device drive 54 BEL External device 1 drive instruction 55 FS External device 1 drive instruction (real time) 56 SUB External device 2 drive instruction (real time) 57 EM External device 2 drive instruction (real time) 58 ENQ Inquire ENQ status 59 EOT Inquire
  • Samsung SRP-275CEPG | Operation Manual - Page 73
    5.4.5 Commands list for CITIZEN mode (iDP3550/3551) n Command Description Hex 1 FF n n-line paper feed (CBM1 mode) 0C n 2 FF Form feed (CBM2 mode) 0C 3 SO (Note) Specifying the double width character (CBM1 mode) 0E 4 SI (Note) Canceling the double width character 0F 5 LF Print
  • Samsung SRP-275CEPG | Operation Manual - Page 74
    CHAPTER 5 CONTROL COMMANDS LIST Command SO SI Command DC1 DC2 DC3 ESC "C" n Code 0E 0F Code 11 12 13 1B 43 n 8-bit data selected Specifying the double width character Canceling the double width character Function 7-bit data selected Specifying the shift-out side character Specifying the shift-in
  • Samsung SRP-275CEPG | Operation Manual - Page 75
    CHAPTER 5 CONTROL COMMANDS LIST SO [Name] [Format] [Description] (CBM2 Mode) Specifying the double width character/shift-out side characters ASCII SO Hex 0E The data following this command is printed doubled in the horizontal direction. Double width characters remain valid until the double
  • Samsung SRP-275CEPG | Operation Manual - Page 76
    CHAPTER 5 CONTROL COMMANDS LIST DC1 [Name] Setting the select mode [Format] ASCII DC1 Hex 11 [Description] This command sets the printer in the selecting status. (CBM2 Mode) DC2 (CBM1 Mode) [Name] Specifying/Canceling the inverted character [Format] ASCII DC2 Hex 12 [Description]
  • Samsung SRP-275CEPG | Operation Manual - Page 77
    CHAPTER 5 CONTROL COMMANDS LIST ESC * n1 n2 [Name] Specifying the bit image mode [Format] ASCII ESC * n1 n2 Hex 1B 2A n1 n2 [Range] 1 ≤ n1 + 256 x n2 ≤ 360 (for DP654 mechanism) 1 ≤ n1 + 256 x n2 ≤ 400 (for DP657 mechanism) [Description] This command allows printing in the bit image
  • Samsung SRP-275CEPG | Operation Manual - Page 78
    CHAPTER 5 CONTROL COMMANDS LIST ESC 3 [Name] Specifying the standard line feed width [Format] ASCII ESC 3 Hex 1B 33 [Description] This command sets the line feed width as follows. Character type : 1/6 inch Graphic type : 2/9 inch ESC C n [Name] Setting the page length [Format] ASCII
  • Samsung SRP-275CEPG | Operation Manual - Page 79
    CHAPTER 5 CONTROL COMMANDS LIST ESC t n [Name] Selecting the character code table [Format] ASCll ESC tn Hex 18 74 n [Range] 0 ≤ n ≤ 30 [Description] This command selects code-page. [Default] Depends upon DIP Switch setting. n Page 0 PC437 1 Katakana 2 PC850 3 PC860 4 PC863
  • Samsung SRP-275CEPG | Operation Manual - Page 80
    CHAPTER 5 CONTROL COMMANDS LIST FS [Name] Driving command B for drawer-1 [Format] ASCII FS Hex 1C [Description] This command drives the drawer connector No. 2 pin under the condition set with the ESC BEL n1 n2 command. SUB [[Name] Driving command for drawer-2 [Format] ASCII SUB Hex
  • Samsung SRP-275CEPG | Operation Manual - Page 81
    CHAPTER 5 CONTROL COMMANDS LIST ESC & n1 n2 [m0 m1 m5 m6 m7 m8 m9] n2 - n1 +1 [Name] Defining the download character set [Format] ASCII ESC & n1 n2 [m0 m8 m9] n2-n1+1 Hex 1B 26 00 n1 n2 [m0 m8 m9] n2-n1+1 [Range] 32 ≤ n1 ≤ n2 ≤ 255, m0 = 0 or m0 = 128 [Description] This command
  • Samsung SRP-275CEPG | Operation Manual - Page 82
    CHAPTER 5 CONTROL COMMANDS LIST ESC DC3 n [Name] Printing the message [Format] ASCII ESC DC3 n Hex 1B 13 n [Range] 1 ≤ n ≤ 10 [Function] This command prints a message. If the value of n is specified beyond the range, the message will not be printed. ESC y n [Name] Setting the print
  • Samsung SRP-275CEPG | Operation Manual - Page 83
    CHAPTER 5 CONTROL COMMANDS LIST GS * n1 n2 [d] n1xn2x8 [Name] Defining the download bit image [Format] ASCII GS * n1 n2 m [d] n1xn2x8 Hex 1D 2A n1 n2 m [d] n1xn2x8 [Range] 1 ≤ n1 ≤ 45 0 ≤ n2 ≤ 24 Note) Take care that the number of data (n1 x n2 x 8) is equal to or smaller than 2,048.
  • Samsung SRP-275CEPG | Operation Manual - Page 84
    CHAPTER 5 CONTROL COMMANDS LIST 5.4.4 Command description for STAR mode (SP500) ESC GS t n [Name] Select code page [Format] ASCII ESC GS t n Hex 1B 1D 74 n Decimal 27 29 116 n [Range] 0 ≤ n ≤ 30 [Default] Memory Switch setting [Description] Specifies code page according to n
  • Samsung SRP-275CEPG | Operation Manual - Page 85
    CHAPTER 5 CONTROL COMMANDS LIST ESC M [Name] Specify 7 x 9 font (half dots) (default) [Format] ASCII ESC M Hex 1B 4D Decimal 27 77 [Range] ------ [Default] ------ [Description] Specifies 7 x 9 (half dots) fonts ESC P [Name] Specify 9 x 9 font (half dots) [Format] ASCII ESC P
  • Samsung SRP-275CEPG | Operation Manual - Page 86
    CHAPTER 5 CONTROL COMMANDS LIST ESC W n [Name] Specify/cancel expanded double-wide printing [Format] ASCII ESC W n Hex 1B 57 n Decimal 27 87 n [Range] n = 0, 1, 48, 49 [Default] n = 0 (Double wide printing cancelled) [Description] Specifies/cancels double-wide expanded printing
  • Samsung SRP-275CEPG | Operation Manual - Page 87
    CHAPTER 5 CONTROL COMMANDS LIST ESC - n [Name] Specify/cancel underline mode [Format] ASCII ESC - n Hex 1B 2D n Decimal 27 45 n [Range] n = 0, 1, 48, 49 [Default] n = 0 (Underline cancelled) [Description] Specifies underline according to the n value. n Function 0, 48 Cancel
  • Samsung SRP-275CEPG | Operation Manual - Page 88
    print (clockwise) or to cancel rotation for subsequent data, according to the n value. n Set rotation 0, 48 Cancelled (0° rotation) 1, 49 270° rotation 2, 50 90° rotation Rotated characters cannot be applied with underlines or upperlines. The relationship between double-high and double-wide
  • Samsung SRP-275CEPG | Operation Manual - Page 89
    CHAPTER 5 CONTROL COMMANDS LIST LF Name] Line feed [Format] ASCII LF Hex 0A Decimal 10 [Range] ------ [Default] Set line feed to 1/6 inch [Description] After printing data in the line buffer, paper is fed according to the currently set line feed amount. CR [Name] [Format] Carriage
  • Samsung SRP-275CEPG | Operation Manual - Page 90
    CHAPTER 5 CONTROL COMMANDS LIST ESC z 0 [Name] Set line feed to 1/12 inch [Format] ASCII ESC z 0 or ESC z "0" Hex 1B 7A 00 1B 7A 30 Decimal 27 122 0 27 122 48 [Range] ------ [Default] 1/6 inch [Description] Sets subsequent line feeds to 1/12 inch. ESC z 1 [Name] Set
  • Samsung SRP-275CEPG | Operation Manual - Page 91
    feed. (*2) Paper feed to tear-bar position: Executes a 7/6 inch paper feed. Refer to the explanations on memory switches in each of the printer's product specification manuals for details regarding Memory Switch settings. 5-91
  • Samsung SRP-275CEPG | Operation Manual - Page 92
    CHAPTER 5 CONTROL COMMANDS LIST ESC C n [Name] Set page length to n lines [Format] ASCII ESC C n Hex 1B 43 n Decimal 27 67 n [Range] 1 ≤ n ≤ 255 [Default] 1/6 inch x 42 [Description] This command sets the length of one page to [currently set line feed amount x n] lines. The
  • Samsung SRP-275CEPG | Operation Manual - Page 93
    CHAPTER 5 CONTROL COMMANDS LIST ESC N n [Name] [Format] [Range] [Default] [Description] Set bottom margin to n lines ASCII ESC N n Hex 1B 4E n Decimal 27 78 n 0 ≤ n ≤ 255 n = 0 This command sets the bottom margin position to (current line feed amount x n). ESC O [Name] [Format] [
  • Samsung SRP-275CEPG | Operation Manual - Page 94
    CHAPTER 5 CONTROL COMMANDS LIST ESC l n Name] Set left margin [Format] ASCII ESC l n Hex 1B 6C n Decimal 27 108 n [Range] 0 ≤ n ≤ (Right margin -2) ≤ 255 [Default] n = 0 [Description] This command sets the left margin (current ANK character pitch x n) using the left edge as a
  • Samsung SRP-275CEPG | Operation Manual - Page 95
    CHAPTER 5 CONTROL COMMANDS LIST HT [Name] Move horizontal tab [Format] ASCII HT Hex 09 Decimal 9 [Range] ------ [Default] ------ [Description] Move print position to next horizontal tab position. The current moves to the next tab position when at the horizontal tab position. This
  • Samsung SRP-275CEPG | Operation Manual - Page 96
    CHAPTER 5 CONTROL COMMANDS LIST ESC GS a n [Name] Specify position alignment [Format] ASCII ESC GS a n Hex 1B 1D 61 n Decimal 27 29 97 n [Range] 0 ≤n ≤2 48 ≤ n ≤ 50 ("0" ≤ n ≤ "2") [Default] n = 0 [Description] This specifies position alignment for all data in one line, in
  • Samsung SRP-275CEPG | Operation Manual - Page 97
    CHAPTER 5 CONTROL COMMANDS LIST ESC & NUL n1 n2 [m d1 d2 d3 d4 d5 (d6 d7)]n2-n1+1 [Name] Register/cancel download characters [Format] ASCII ESC & NUL n1 n2[m d1 d2 d3 d4 d5 (d6 d7)]n2-n1+1 Hex 1B 26 00 n1 n2[m d1 d2 d3 d4 d5 (d6 d7)]n2-n1+1 Decimal 27 38 0 n1 n2[m d1 d2 d3 d4 d5 (d6 d7)]n2-n1
  • Samsung SRP-275CEPG | Operation Manual - Page 98
    to the total dot count. Data that exceeds the total dot count or the right margin is ignored. See each printer's product specifications manual for details regarding the total dot count. After printing this bit image, it automatically returns to the character mode. The following drawing shows
  • Samsung SRP-275CEPG | Operation Manual - Page 99
    external device (such as cash drawers). Energizing time = 10 x n1 (ms) After printing, this is executed by BEL (External device 1 drive instruction) or FS (External device 1 drive instruction (real time)). This command is ignored when n1 and n2 are out of range. - n1 = 0 or n2 = 0: This command is
  • Samsung SRP-275CEPG | Operation Manual - Page 100
    the EM command. [Note] External device 1 and external device 2 cannot be executed simultaneously EM [Name] External device 2 drive instruction (real time) [Format] ASCII EM Hex 19 Decimal 25 [Range] ------ [Default] ------ [Description] Drives external device 2. The energizing time
  • Samsung SRP-275CEPG | Operation Manual - Page 101
    CHAPTER 5 CONTROL COMMANDS LIST ENQ [Name] [Format] Decimal [Range] [Default] [Description] Inquire ENQ status ASCII ENQ Hex 05 5 ------ ------ This command is effective only when using an interface capable of bi-directional data communications. When this command is received, the printer
  • Samsung SRP-275CEPG | Operation Manual - Page 102
    CHAPTER 5 CONTROL COMMANDS LIST ESC ACK SOH [Name] Inquire status [Format] ASCII ESC ACK SOH Hex 1B 06 01 Decimal 27 6 1 [Range] ------ [Default] ------ [Description] This command is effective only when using an interface capable of bi-directional data communications. When this
  • Samsung SRP-275CEPG | Operation Manual - Page 103
    CHAPTER 5 CONTROL COMMANDS LIST Printer status 2 Error information (Fourth byte) Bit Contents 7 Fixed at "0" Stopped by high head 6 temperature 5 Non-recoverable error 4 Fixed at "0" 3 Auto-cutter error 2 Mechanical error 1 Not used (Fixed at "0") 0 Fixed at "0" Status "0" Not
  • Samsung SRP-275CEPG | Operation Manual - Page 104
    CHAPTER 5 CONTROL COMMANDS LIST ESC RS a n [Name] [Format] [Range] [Default] [Description] Sets auto status transmission conditions ASCII ESC RS a n Hex 1B 1E 61 n Decimal 27 30 97 n 0 ≤n ≤3 48 ≤ n ≤ 51 ("0" ≤ n ≤ "3") DIP Switch or Memory Switch setting This command is
  • Samsung SRP-275CEPG | Operation Manual - Page 105
    CHAPTER 5 CONTROL COMMANDS LIST ESC RS E n [Name] Clear the ETB counter and ETB status 30 69 n [Format] ASCII ESC RS E n Hex 1B 1E 45 n Decimal 27 30 69 n [Range] n = 0 n = 48 ("0") [Default] ------ [Description] Clears the ASB ETB counter to zero and clears the auto status 1
  • Samsung SRP-275CEPG | Operation Manual - Page 106
    CHAPTER 5 CONTROL COMMANDS LIST ESC @ [Name] Command initialization [Format] ASCII ESC @ Hex 1B 40 Decimal 27 64 [Range] ------ [Default] ------ [Description] Initializes each command after printing data in the line buffer. DIP Switch is not reread. The following shows the
  • Samsung SRP-275CEPG | Operation Manual - Page 107
    CHAPTER 5 CONTROL COMMANDS LIST ESC ? LF NUL [Name] Reset printer and execute self print [Format] ASCII ESC ? LF NUL Hex 1B 3F 0A 00 Decimal 27 63 10 0 [Range] ------ [Default] ------ [Description] Hardware resets the printer and executes on self print. After sending this
  • Samsung SRP-275CEPG | Operation Manual - Page 108
    6 CHAPTER CONTENTS REFERENCE INFORMATION 6.1 Printing specification 6-2 6.2 Paper specification 6-2 6.3 Ribbon cassette specification 6-2 6.4 Electrical characteristics 6-3 6.5 Reliability 6-3 6.6 Environmental 6-3 6.7 Dimensions & Weight 6-4 6.8 Optional features 6-4
  • Samsung SRP-275CEPG | Operation Manual - Page 109
    Red) Black & Red 13 mm (W) x 6 mm (L) Black : 1,500,000 characters Red : 750,000 characters Remark Continuous printing 7 x 9 font ASCII 25°C Malfunctions and other problems may arise if other than specified ribbon cassettes are used in the printer. The new settings take effect when you turn on the
  • Samsung SRP-275CEPG | Operation Manual - Page 110
    Shipping Wt. : 3.4 kg 6.8 Optional features The optional features either replace a standard feature or enhance the operation of the printer. All be selected when the printer is ordered. - Auto cutter (SRP-275A : Exclude auto cutter, SRP-275C : Including auto cutter) - Interface (Serial / Parallel
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
printed in korea
2004. 09
Operator
’
s manual
POS impact dot matrix printer
SRP-275
ELECTRO -
MECHANICS
ELECTRO -
MECHANICS