SanDisk SDSDH-1024 Product Manual - Page 70

Example for Switching

Get SanDisk SDSDH-1024 - 1GB SD Card Ultra II PDF manuals and user guides
UPC - 710348911073
View all SanDisk SDSDH-1024 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Revision 2.2 Chapter 4 - SD Card Protocol Description SanDisk SD Card Product Manual Case (2) - Check function with error CMD6 argument = '0000 0000 1111 1000 1111 0010 0000 0001' Read Data = [511:496] = '0000 0000 0000 0000' (means error) [495:400] = '1000 0000 0000 0001' & '1000 0000 0000 0001' & '1000 0000 0000 0001'& '1000 0000 0000 0001' & '1000 0000 0000 0011' & '1000 0000 0000 0011' [399:376] = '0000 1111 0000 1111 0000 0001' [375:0] = Reserved (All 0s) Error Example for Switching Card condition Support function = command system : For eC(0x1), access mode : High-speed(0x1) Current function = command system : For eC(0x1), access mode : Default(0x0) Switch example : command system : For eC => Default, access mode : Default => High-speed Case (3) - Switch function with no error CMD6 argument = '1000 0000 1111 1111 1111 1111 0000 0001' Read Data = [511:496] = '0000 0000 0010 0000' (=64mA) [495:400] = '1000 0000 0000 0001' & '1000 0000 0000 0001' & '1000 0000 0000 0001'& '1000 0000 0000 0001' & '1000 0000 0000 0011' & '1000 0000 0000 0011' [399:376] = '0000 0000 0000 0000 0000 0001' [375:0] = Reserved (All 0s) For eC High-speed Case (4) - Switch function with error No influence Default CMD6 argument = '1000 0000 1111 1000 1111 0010 0000 0001' Read Data = [511:496] = '0000 0000 0000 0000' (means error) [495:400] = '1000 0000 0000 0001' & '1000 0000 0000 0001' & '1000 0000 0000 0001'& '1000 0000 0000 0001' & '1000 0000 0000 0011' & '1000 0000 0000 0011' [399:376] = '0000 1111 0000 1111 0001 0000' [375:0] = Reserved (All 0s) 4.4.11 Error High-speed Mode19 (25MB/sec interface speed) Although revision 1.01 of the SD Physical Layer Specification supports up to 12.5MB/sec interface speed, the speed of 25MB/sec is necessary to support increasing performance needs of the host and because of growing memory size. To achieve the 25MB/sec interface speed, the clock rate is increased to 50MHz and CLK/CMD/DAT signal timing and circuit conditions are reconsidered and changed from Physical Layer Specification Version 1.01. After power-up, the SD Card is in Default Speed mode. Revision 1.10 (and greater) SD cards can be placed in high-speed mode using the Switch Function command (CMD6). The high-speed function belongs to access mode group. 19 High-speed mode is not supported in SPI Mode. © 2004 SanDisk Corporation 4-26 12/08/04

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
Chapter 4 – SD Card Protocol Description
Revision 2.2
SanDisk SD Card Product Manual
© 2004 SanDisk Corporation
4-26
12/08/04
Case (2)
– Check function with error
CMD6 argument = ‘0000 0000 1111 1000 1111 0010 0000 0001’
Read Data = [511:496] = ‘0000 0000 0000 0000’ (means error)
[495:400] = ‘1000 0000 0000 0001’ & ‘1000 0000 0000 0001’ & ‘1000 0000 0000 0001’&
‘1000 0000 0000 0001’ & ‘1000 0000 0000 0011’ & ‘1000 0000 0000 0011’
[399:376] = ‘0000 1111 0000 1111 0000 0001’
[375:0] = Reserved (All 0s)
Example for Switching
Card condition
Support function = command system : For eC(0x1),
access mode : High-speed(0x1)
Current function = command system : For eC(0x1),
access mode : Default(0x0)
Switch example : command system : For eC => Default,
access mode : Default => High-speed
Case (3)
– Switch function with no error
CMD6 argument = ‘1000 0000 1111 1111 1111 1111 0000 0001’
Read Data = [511:496] = ‘0000 0000 0010 0000’ (=64mA)
[495:400] = ‘1000 0000 0000 0001’ & ‘1000 0000 0000 0001’ & ‘1000 0000 0000 0001’&
‘1000 0000 0000 0001’ & ‘1000 0000 0000 0011’ & ‘1000 0000 0000 0011’
[399:376] = ‘0000 0000 0000 0000 0000 0001’
[375:0] = Reserved (All 0s)
Case (4)
– Switch function with error
CMD6 argument = ‘1000 0000 1111 1000 1111 0010
0000 0001’
Read Data = [511:496] = ‘0000 0000 0000
0000
’ (means error)
[495:400] = ‘1000 0000 0000 0001’ & ‘1000 0000 0000 0001’ & ‘1000 0000 0000 0001’&
‘1000 0000 0000 0001’ & ‘1000 0000 0000 0011’ & ‘1000 0000 0000 0011’
[399:376] = ‘0000 1111
0000 1111
0001 0000’
[375:0] = Reserved (All 0s)
4.4.11
High-speed Mode
19
(25MB/sec interface speed)
Although revision 1.01 of the SD Physical Layer Specification supports up to 12.5MB/sec
interface speed, the speed of 25MB/sec is necessary to support increasing performance
needs of the host and because of growing memory size.
To achieve the 25MB/sec interface speed, the clock rate is increased to 50MHz and
CLK/CMD/DAT signal timing and circuit conditions are reconsidered and changed from
Physical Layer Specification Version 1.01.
After power-up, the SD Card is in Default Speed mode. Revision 1.10 (and greater) SD
cards can be placed in high-speed mode using the Switch Function command (CMD6).
The high-speed function belongs to access mode group.
19
High-speed mode is not supported in SPI Mode.
For eC
No influence
High-speed
Default
Error
Error