Home » TP-Link Manuals » Hubs & Switches » TP-Link TL-SG3216 » Manual Viewer

TP-Link TL-SG3216 TL-SG3216 V1 User Guide - Page 40

LAG

Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Select: Port: Max Learned MAC: Learned Num: Learn Mode: Status: Select the desired port for Port Security configuration. It is multi-optional. Displays the port number. Specify the maximum number of MAC addresses that can be learned on the port. Displays the number of MAC addresses that have been learned on the port. Select the Learn Mode for the port. • Dynamic: When Dynamic mode is selected, the learned MAC address will be deleted automatically after the aging time. • Static: When Static mode is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be cleared after the switch is rebooted. • Permanent: When Permanent mode is selected, the learned MAC address will be out of the influence of the aging time and can only be deleted manually. The learned entries will be saved even the switch is rebooted. Select Enable/Disable the Port Security feature for the port. Note: 1. The Port Security function is disabled for the LAG port member. Only the port is removed from the LAG, will the Port Security function be available for the port. 2. The Port Security function is disabled when the 802.1X function is enabled. 5.2 LAG LAG (Link Aggregation Group) is to combine a number of ports together to make a single high-bandwidth data path, so as to implement the traffic load sharing among the member ports in the group and to enhance the connection reliability. For the member ports in an aggregation group, their basic configuration must be the same. The basic configuration includes STP, QoS, GVRP, VLAN, port attributes, MAC Address Learning mode and other associated settings. The further explains are following: z If the ports, which are enabled for the GVRP, 802.1Q VLAN, Voice VLAN, STP, QoS, DHCP Snooping and Port Configuration (Speed and Duplex, Flow Control), are in a LAG, their configurations should be the same. z The ports, which are enabled for the Port Security, Port Mirror, MAC Address Filtering, Static MAC Address Binding and 802.1X Authentication, can not be added to the LAG. z It's not suggested to add the ports with ARP Inspection and DoS Defend enabled to the LAG. If the LAG is needed, you are suggested to configure the LAG function here before configuring the other functions for the member ports. 33

Section	Page
Package Contents	8
Chapter 1 About this Guide	9
1.1 Intended Readers	9
1.2 Conventions	9
1.3 Overview of This Guide	9
Chapter 2 Introduction	13
2.1 Overview of the Switch	13
2.2 Main Features	13
2.3 Appearance Description	14
2.3.1 Front Panel	14
2.3.2 Rear Panel	15
Chapter 3 Login to the Switch	16
3.1 Login	16
3.2 Configuration	16
Chapter 4 System	18
4.1 System Info	18
4.1.1 System Summary	18
4.1.2 Device Description	20
4.1.3 System Time	20
4.1.4 System IP	22
4.2 User Manage	23
4.2.1 User Table	23
4.2.2 User Config	23
4.3 System Tools	25
4.3.1 Config Restore	25
4.3.2 Config Backup	25
4.3.3 Firmware Upgrade	26
4.3.4 System Reboot	27
4.3.5 System Reset	27
4.4 Access Security	27
4.4.1 Access Control	27
4.4.2 SSL Config	29
4.4.3 SSH Config	30
Chapter 5 Switching	36
5.1 Port	36
5.1.1 Port Config	36
5.1.2 Port Mirror	37
5.1.3 Port Security	39
5.2 LAG	40
5.2.1 LAG Table	41
5.2.2 Static LAG	42
5.2.3 LACP Config	43
5.3 Traffic Monitor	45
5.3.1 Traffic Summary	45
5.3.2 Traffic Statistics	46
5.4 MAC Address	47
5.4.1 Address Table	48
5.4.2 Static Address	50
5.4.3 Dynamic Address	51
5.4.4 Filtering Address	53
Chapter 6 VLAN	55
6.1 802.1Q VLAN	56
6.1.1 VLAN Config	58
6.1.2 Port Config	60
6.2 MAC VLAN	62
6.3 Protocol VLAN	63
6.3.1 Protocol Group Table	66
6.3.2 Protocol Group	66
6.3.3 Protocol Template	67
6.4 Application Example for 802.1Q VLAN	68
6.5 Application Example for MAC VLAN	70
6.6 Application Example for Protocol VLAN	71
6.7 GVRP	73
Chapter 7 Spanning Tree	77
7.1 STP Config	82
7.1.1 STP Config	82
7.1.2 STP Summary	84
7.2 Port Config	84
7.3 MSTP Instance	86
7.3.1 Region Config	86
7.3.2 Instance Config	87
7.3.3 Instance Port Config	88
7.4 STP Security	90
7.4.1 Port Protect	90
7.4.2 TC Protect	93
7.5 Application Example for STP Function	93
Chapter 8 Multicast	97
8.1 IGMP Snooping	99
8.1.1 Snooping Config	100
8.1.2 Port Config	101
8.1.3 VLAN Config	102
8.1.4 Multicast VLAN	104
8.2 Multicast IP	107
8.2.1 Multicast IP Table	108
8.2.2 Static Multicast IP	108
8.3 Multicast Filter	109
8.3.1 IP-Range	110
8.3.2 Port Filter	111
8.4 Packet Statistics	112
Chapter 9 QoS	114
9.1 DiffServ	117
9.1.1 Port Priority	117
9.1.2 Schedule Mode	118
9.1.3 802.1P Priority	119
9.1.4 DSCP Priority	119
9.2 Bandwidth Control	121
9.2.1 Rate Limit	121
9.2.2 Storm Control	122
9.3 Voice VLAN	123
9.3.1 Global Config	125
9.3.2 Port Config	126
9.3.3 OUI Config	127
Chapter 10 ACL	129
10.1 Time-Range	129
10.1.1 Time-Range Summary	129
10.1.2 Time-Range Create	130
10.1.3 Holiday Config	131
10.2 ACL Config	131
10.2.1 ACL Summary	132
10.2.2 ACL Create	132
10.2.3 MAC ACL	133
10.2.4 Standard-IP ACL	134
10.2.5 Extend-IP ACL	134
10.3 Policy Config	136
10.3.1 Policy Summary	136
10.3.2 Policy Create	137
10.3.3 Action Create	137
10.4 Policy Binding	138
10.4.1 Binding Table	138
10.4.2 Port Binding	139
10.4.3 VLAN Binding	139
10.5 Application Example for ACL	140
Chapter 11 Network Security	143
11.1 IP-MAC Binding	143
11.1.1 Binding Table	143
11.1.2 Manual Binding	144
11.1.3 ARP Scanning	146
11.1.4 DHCP Snooping	147
11.2 ARP Inspection	153
11.2.1 ARP Detect	157
11.2.2 ARP Defend	158
11.2.3 ARP Statistics	159
11.3 DoS Defend	160
11.4 802.1X	162
11.4.1 Global Config	166
11.4.2 Port Config	168
11.4.3 Radius Server	169
Chapter 12 SNMP	171
12.1 SNMP Config	173
12.1.1 Global Config	173
12.1.2 SNMP View	174
12.1.3 SNMP Group	175
12.1.4 SNMP User	176
12.1.5 SNMP Community	178
12.2 Notification	180
12.3 RMON	182
12.3.1 History Control	183
12.3.2 Event Config	183
12.3.3 Alarm Config	184
Chapter 13 Cluster	187
13.1 NDP	188
13.1.1 Neighbor Info	188
13.1.2 NDP Summary	189
13.1.3 NDP Config	191
13.2 NTDP	192
13.2.1 Device Table	192
13.2.2 NTDP Summary	193
13.2.3 NTDP Config	194
13.3 Cluster	196
13.3.1 Cluster Summary	196
13.3.2 Cluster Config	197
13.4 Application Example for Cluster Function	199
Chapter 14 Maintenance	202
14.1 System Monitor	202
14.1.1 CPU Monitor	202
14.1.2 Memory Monitor	203
14.2 Log	204
14.2.1 Log Table	205
14.2.2 Local Log	205
14.2.3 Remote Log	206
14.2.4 Backup Log	207
14.3 Device Diagnose	208
14.3.1 Cable Test	208
14.3.2 Loopback	209
14.4 Network Diagnose	209
14.4.1 Ping	209
14.4.2 Tracert	210
Appendix A: Specifications	212
Appendix B: Configuring the PCs	213
Appendix C: Load Software using FTP	216
Appendix D: 802.1X Client Software	221

Match case Limit results 1 per page

Select:

Select the desired port for Port Security configuration. It is

multi-optional.

Port:

Displays the port number.

Max Learned MAC:

Specify the maximum number of MAC addresses that can be

learned on the port.

Learned Num:

Displays the number of MAC addresses that have been learned

on the port.

Learn Mode:

Select the Learn Mode for the port.

•

Dynamic:

When Dynamic mode is selected, the learned

MAC address will be deleted automatically after the aging

time.

•

Static:

When Static mode is selected, the learned MAC

address will be out of the influence of the aging time and

can only be deleted manually. The learned entries will be

cleared after the switch is rebooted.

•

Permanent:

When Permanent mode is selected, the

learned MAC address will be out of the influence of the

aging time and can only be deleted manually. The learned

entries will be saved even the switch is rebooted.

Status:

Select Enable/Disable the Port Security feature for the port.

Note:

The Port Security function is disabled for the LAG port member. Only the port is removed from

the LAG, will the Port Security function be available for the port.

The Port Security function is disabled when the 802.1X function is enabled.

5.2 LAG

LAG (Link Aggregation Group) is to combine a number of ports together to make a single

high-bandwidth data path, so as to implement the traffic load sharing among the member ports in

the group and to enhance the connection reliability.

For the member ports in an aggregation group, their basic configuration must be the same. The

basic configuration includes

STP

QoS

GVRP

VLAN

port attributes

MAC Address Learning

mode

and other associated settings. The further explains are following:

If the ports, which are enabled for the

GVRP

802.1Q VLAN

Voice VLAN

STP

QoS

DHCP

Snooping

and

Port Configuration

(

Speed and Duplex

Flow Control

), are in a LAG, their

configurations should be the same.

The ports, which are enabled for the

Port Security

Port Mirror

MAC Address Filtering

Static MAC Address Binding

and

802.1X Authentication

, can not be added to the LAG.

It’s not suggested to add the ports with

ARP Inspection

and

DoS Defend

enabled to the

LAG.

If the LAG is needed, you are suggested to configure the LAG function here before configuring the

other functions for the member ports.