Toshiba 40SL500U Owners Manual - Page 35

Configuring the antenna input, source for the ANT/CABLE terminal, Programming channels into the, TV'

Get Toshiba 40SL500U PDF manuals and user guides View all Toshiba 40SL500U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Chapter 5: Setting up your TV Configuring the antenna input source for the ANT/CABLE terminal 1 From the SETUP menu, highlight ANT/CABLE In. 2 Press C or c to select the input source (Antenna or Cable) for the ANT/CABLE input and press . EXIT Programming channels into the TV's channel memory When you press < or , on the remote control or TV control panel, your TV will stop only on the channels you programmed into the TV's channel memory. Follow the steps below to program channels into the TV's channel memory. Auto Tuning Your TV can automatically detect all active channels in your area and store them in its memory. After the channels are programmed automatically, you can manually add or erase individual channels in the channel memory. Note: • You must configure the ANT/CABLE input source before programming channels. • If the ANT/CABLE input is configured for Cable, the automatic channel programming process erases channels that were previously programmed into the TV's memory. • If the ANT/CABLE input is configured for Antenna, the automatic channel programming process adds newly found channels to the existing set of programmed channels (and does NOT erase channels that were previously programmed into the TV's memory). To remove an Antenna source channel from the memory, you must set it to Skip (- "Setting channel skip" on page 36). • To tune the TV to a channel not programmed in the channel memory, you must use the number buttons on the remote control. • Programming channels when the ANT/CABLE input is configured for Cable will take substantially longer than when the antenna input is configured for Antenna. This is normal; however, once channel programming is finished, you should not have to repeat the programming process again unless your Cable TV service lineup changes significantly. 1 Configure the ANT/CABLE input, if you have not already done so (- left-hand column). 2 From the SETUP menu, highlight Auto Tuning and press . OK 3 A screen will appear warning that previous programs and settings will be deleted. 4 Press OK to start Auto Tuning. The TV will automatically cycle through all the channels, and store all active channels in the channel memory. When Auto Tuning is finished, press < or , to view the programmed channels. Manual Tuning After automatically programming channels into the channel memory, you can manually enter channels if the physical channel is known. 1 From the SETUP menu, highlight Manual Tuning and press . OK 2 Use the Channel Numbers on the remote control to enter the channel number (up to three-digit number) and press . OK 3 Press OK to start Manual Tuning. If channels are found, they will be listed at the bottom of the screen. Analog channels will be noted by an "ATV" symbol and digital channels by a "DTV" symbol. 35 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
35
Chapter 5: Setting up your TV
Configuring the antenna input
source for the ANT/CABLE terminal
1
From the
S
ETUP
menu, highlight
ANT/CABLE In
.
2
Press
C
or
c
to select the input source (
Antenna
or
Cable
) for the
ANT/CABLE
input and press
.
Programming channels into the
TV’s channel memory
When you press
<
or
,
on the remote control or TV
control panel, your TV will stop only on the channels
you programmed into the TV’s channel memory.
Follow the steps below to program channels into the
TV’s channel memory.
Auto Tuning
Your TV can automatically detect all active channels in
your area and store them in its memory. After the
channels are programmed automatically, you can
manually add or erase individual channels in the
channel memory.
Note:
•
You must configure the ANT/CABLE input source before
programming channels.
•
If the ANT/CABLE input is configured for
Cable
, the
automatic channel programming process erases
channels that were previously programmed into the TV’s
memory.
•
If the ANT/CABLE input is configured for
Antenna
, the
automatic channel programming process adds newly
found channels to the existing set of programmed
channels (and does NOT erase channels that were
previously programmed into the TV’s memory). To
remove an Antenna source channel from the memory,
you must set it to Skip (
-
“Setting channel skip” on page
36).
•
To tune the TV to a channel not programmed in the
channel memory, you must use the number buttons on
the remote control.
•
Programming channels when the ANT/CABLE input is
configured for
Cable
will take substantially longer than
when the antenna input is configured for
Antenna
. This
is normal; however, once channel programming is
finished, you should not have to repeat the programming
process again unless your Cable TV service lineup
changes significantly.
1
Configure the
ANT/CABLE
input, if you have not
already done so (
-
left-hand column).
2
From the
S
ETUP
menu, highlight
Auto Tunin
g
and
press
.
3
A screen will appear warning that previous
programs and settings will be deleted.
4
Press
to start Auto Tuning.
The TV will automatically cycle through all the
channels, and store all active channels in the
channel memory. When Auto Tuning is finished,
press
<
or
,
to view the programmed channels.
Manual Tuning
After automatically programming channels into the
channel memory, you can manually enter channels if
the physical channel is known.
1
From the
S
ETUP
menu, highlight
Manual Tunin
g
and press
.
2
Use the Channel Numbers on the remote control to
enter the channel number (up to three-digit
number) and press
.
3
Press
to start Manual Tuning.
If channels are found, they will be listed at the bottom
of the screen.
Analog channels will be noted by an
“ATV” symbol and digital channels by a “DTV”
symbol.
EXIT
OK
OK
OK
OK
OK
Downloaded from
www.Manualslib.com
manuals search engine