Xerox 4540 Service Manual - Page 151

To Replace a Hard Drive (CRU), Replace the disk drives access cover

Get Xerox 4540 - Phaser Copystation PDF manuals and user guides View all Xerox 4540 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 151 highlights

11. Replace the disk drives access cover and, using a No. 1 Phillips screwdriver, tighten the two screws on the left and right sides. See Section t, "To Remove the Drives Access Cover" on page 3-13. ▼ To Replace a Hard Drive (CRU) This section describes how to remove and replace a drive. It is a good practice to allocate five drives (roughly 10 percent of the total capacity) as hot spares. Note - This component is a hot-pluggable CRU and can be replaced by anyone. Hot-pluggable means that the disk drive must be first brought offline by using a management software or operating system command; however, the server does not need to be powered off. The system designation of the drives is shown on the service label. TABLE 3-10 lists the qualified part numbers for this component. These part numbers are subject to change over time. Note - Do not mix drives of different drive capacities. For an updated list of components, see the following web site: http://sunsolve.sun.com/handbook_pub/Systems/ TABLE 3-10 Hard Drives for the X4500 Server Disk Drive Seagate 250GB SATA 3.5" drive (X4500) Hitachi 500GB, SATA, 3.5" drive (X4500, X4540) Hitachi 750GB, SATA, 3.5" drive (X4500, migrated X4540*) Hitachi 1-TB , SATA 3.5" drive (X4500, X4540) Part Number #541-1468, XRA-ST1CH-250G7KZ (X-option) #541-3050, XRA-ST1CH-500G7KZ (X-option) #540-7244, XRA-ST1CH-750G7KZ (X-option) #540-7507, XRA-ST1CH-1T7K (X-option) Chapter 3 Maintaining the Sun Fire X4500 and X4540 Servers 3-31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
Chapter 3
Maintaining the Sun Fire X4500 and X4540 Servers
3-31
11. Replace the disk drives access cover and, using a No. 1 Phillips screwdriver,
tighten the two screws on the left and right sides. See
Section t, “To Remove the
Drives Access Cover” on page 3-13
.
▼
To Replace a Hard Drive (CRU)
This section describes how to remove and replace a drive. It is a good practice to
allocate five drives (roughly 10 percent of the total capacity) as hot spares.
Note –
This component is a hot-pluggable CRU and can be replaced by anyone.
Hot-pluggable means that the disk drive must be first brought offline by using a
management software or operating system command; however, the server does not
need to be powered off.
The system designation of the drives is shown on the service label.
TABLE 3-10
lists the qualified part numbers for this component. These part numbers
are subject to change over time.
Note –
Do not mix drives of different drive capacities.
For an updated list of components, see the following web site:
TABLE 3-10
Hard Drives for the X4500 Server
Disk Drive
Part Number
Seagate 250GB SATA 3.5” drive (X4500)
#541-1468,
XRA-ST1CH-250G7KZ (X-option)
Hitachi 500GB, SATA, 3.5” drive (X4500, X4540)
#541-3050,
XRA-ST1CH-500G7KZ (X-option)
Hitachi 750GB, SATA, 3.5” drive (X4500, migrated
X4540*)
#540-7244,
XRA-ST1CH-750G7KZ (X-option)
Hitachi 1-TB , SATA 3.5" drive (X4500, X4540)
#540-7507,
XRA-ST1CH-1T7K (X-option)