Xerox 4540 Service Manual - Page 175
Inspect the heat sink for dust and lint. Clean if necessary., Unpack the new CPU.
![]() |
View all Xerox 4540 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 175 highlights
Tip - As you pull off the heat sink, the springs in the heat sink screws might pop out. Be prepared to retrieve them. 5. Remove the CPU by pulling the socket release lever out and up. See FIGURE 3-26 (the X4540 system is shown). FIGURE 3-26 Removing the CPU (X4540 shown) Key 6. Use the included alcohol pad to remove all thermal grease from the bottom of the heat sink. 7. Inspect the heat sink for dust and lint. Clean if necessary. 8. Unpack the new CPU. 9. Install the new CPU, or reinstall the existing CPU. Chapter 3 Maintaining the Sun Fire X4500 and X4540 Servers 3-55
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
![]() |
![]() |
![](/manual_guide/products/xerox-4540-service-manual-31966a4/175.png)
Chapter 3
Maintaining the Sun Fire X4500 and X4540 Servers
3-55
Tip –
As you pull off the heat sink, the springs in the heat sink screws might pop
out. Be prepared to retrieve them.
5. Remove the CPU by pulling the socket release lever out and up. See
FIGURE 3-26
(the X4540 system is shown).
FIGURE 3-26
Removing the CPU (X4540 shown)
6. Use the included alcohol pad to remove all thermal grease from the bottom of
the heat sink.
7. Inspect the heat sink for dust and lint. Clean if necessary.
8. Unpack the new CPU.
9. Install the new CPU, or reinstall the existing CPU.
Key