Xerox 4540 Service Manual - Page 195
Lift the system controller handle until its latch clicks into place.
View all Xerox 4540 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 195 highlights
FIGURE 3-33 Replacing the System Controller 5. Push the system controller further until it is seated firmly. Close the system controller handle. 6. Lift the system controller handle until its latch clicks into place. 7. Connect the power cables to both power supplies and make sure to use the power cord retaining clips to keep power cords attached snugly. 8. Replace the cable management assembly if necessary. See one of the following docs depending on your CMA version: ■ Sun Fire X4500/X4540 Installation Guide ■ Sun X4500-J Slide Rail Installation Guide (X4500) ■ "Early-Production Slide Rail and CMA Information" on page G-1 (X4500) Chapter 3 Maintaining the Sun Fire X4500 and X4540 Servers 3-75
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
Chapter 3
Maintaining the Sun Fire X4500 and X4540 Servers
3-75
FIGURE 3-33
Replacing the System Controller
5. Push the system controller further until it is seated firmly. Close the system
controller handle.
6. Lift the system controller handle until its latch clicks into place.
7. Connect the power cables to both power supplies and make sure to use the
power cord retaining clips to keep power cords attached snugly.
8. Replace the cable management assembly if necessary.
See one of the following docs depending on your CMA version:
■
Sun Fire X4500/X4540 Installation Guide
■
Sun X4500-J Slide Rail Installation Guide
(X4500)
■
“Early-Production Slide Rail and CMA Information” on page G-1
(X4500)