ZyXEL ARMOR Z1 User Guide - Page 143

Restart Screen, 15.9 Language Screen

Page 143 highlights

Chapter 15 Maintenance Table 58 Expert > Maintenance > Backup/Restore (continued) LABEL DESCRIPTION Upload Click Upload to begin the upload process. Note: Do not turn off the ARMOR Z1 while configuration file upload is in progress. Reset After you see a "configuration upload successful" screen, you must then wait one minute before logging into the ARMOR Z1 again. The ARMOR Z1 automatically restarts in this time causing a temporary network disconnect. If you see an error screen, click Back to return to the Backup/Restore screen. Pressing the Reset button in this section clears all user-entered configuration information and returns the ARMOR Z1 to its factory defaults. You can also press the RESET button on the rear panel to reset the factory defaults of your ARMOR Z1. Refer to the chapter about introducing the Web Configurator for more information on the RESET button. Note: If you uploaded the default configuration file you may need to change the IP address of your computer to be in the same subnet as that of the default ARMOR Z1 IP address (192.168.1.1). See Appendix C on page 173 for details on how to set up your computer's IP address. 15.8 Restart Screen System restart allows you to reboot the ARMOR Z1 without turning the power off. Click Expert > Maintenance > Restart to open the following screen. Figure 94 Expert > Maintenance > Restart Click Restart to have the ARMOR Z1 reboot. This does not affect the ARMOR Z1's configuration. 15.9 Language Screen Use this screen to change the language for the Web Configurator. Select the language you prefer and click Apply. The Web Configurator language changes after a while without restarting the ARMOR Z1. Click Expert > Maintenance > Language to open the following screen. ARMOR Z1 User's Guide 143

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215

Chapter 15 Maintenance
ARMOR Z1 User’s Guide
143
Note: If you uploaded the default configuration file you may need to change the IP
address of your computer to be in the same subnet as that of the default ARMOR
Z1 IP address (192.168.1.1). See
Appendix C on page 173
for details on how to set
up your computer’s IP address.
15.8
Restart Screen
System restart allows you to reboot the ARMOR Z1 without turning the power off.
Click
Expert
>
Maintenance
>
Restart
to open the following screen.
Figure 94
Expert > Maintenance > Restart
Click
Restart
to have the ARMOR Z1 reboot. This does not affect the ARMOR Z1's configuration.
15.9
Language Screen
Use this screen to change the language for the Web Configurator.
Select the language you prefer and click
Apply
. The Web Configurator language changes after a
while without restarting the ARMOR Z1. Click
Expert
>
Maintenance
>
Language
to open the
following screen.
Upload
Click
Upload
to begin the upload process.
Note: Do not turn off the ARMOR Z1 while configuration file upload is in progress.
After you see a “configuration upload successful” screen, you must then wait one minute
before logging into the ARMOR Z1 again. The ARMOR Z1 automatically restarts in this time
causing a temporary network disconnect.
If you see an error screen, click Back to return to the Backup/Restore screen.
Reset
Pressing the
Reset
button in this section clears all user-entered configuration information
and returns the ARMOR Z1 to its factory defaults.
You can also press the
RESET
button on the rear panel to reset the factory defaults of your
ARMOR Z1. Refer to the chapter about introducing the Web Configurator for more
information on the
RESET
button.
Table 58
Expert > Maintenance > Backup/Restore (continued)
LABEL
DESCRIPTION