ZyXEL P-100 User Guide - Page 46

TCP/IP Ethernet and DHCP Setup

Get ZyXEL P-100 PDF manuals and user guides View all ZyXEL P-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Prestige 100WH Internet Access Router The General Setup menu allows you to define the filter sets that you wish to apply to your Ethernet traffic. From Menu 3 - Ethernet Setup, enter 1 to go to Menu 3.1 -General Ethernet Setup. Menu 3.1 - General Ethernet Setup Input Filter Sets= Output Filter Sets= Press ENTER to Confirm or ESC to Cancel: Figure 3-2. Menu 3.1 - General Ethernet Setup Filters are not required for your Prestige to function properly. However, input and output filter sets may be useful to block certain packets, reduce traffic, and prevent a security breach on your Ethernet. If you have a need for filters, read about Chapter 7 - Filter Set Configuration, then return to this menu to define the appropriate filter sets. 3.2 TCP/IP Ethernet and DHCP Setup 3.2.1 IP Address and Subnet Mask The Prestige is pre-configured in the factory with an IP address of 192.168.1.1 and a subnet mask of 255.255.255.0 (Class C). This setup should work fine for the basic Internet access application. It is strongly recommend that you do not change them, unless your ISP or network administrator assigns you a block of registered IP addresses. 3-2 Chapter 3 Internet Access Application

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
Prestige 100WH Internet Access Router
3-2
Chapter 3
Internet Access Application
The General Setup menu allows you to define the filter sets that you wish to apply to your
Ethernet traffic. From Menu 3 - Ethernet Setup, enter 1 to go to Menu 3.1 -General Ethernet
Setup.
Figure 3-2.
Menu 3.1 - General Ethernet Setup
Filters are not required for your
Prestige
to function properly. However, input and output filter
sets may be useful to block certain packets, reduce traffic, and prevent a security breach on
your Ethernet.
If you have a need for filters, read about
Chapter 7 - Filter Set Configuration
,
then return to
this menu to define the appropriate filter sets.
3.2
TCP/IP Ethernet and DHCP Setup
3.2.1
IP Address and Subnet Mask
The
Prestige
is pre-configured in the factory with an IP address of 192.168.1.1 and a subnet
mask of 255.255.255.0 (Class C). This setup should work fine for the basic Internet access
application. It is strongly recommend that you do not change them, unless your ISP or
network administrator assigns you a block of registered IP addresses.
Menu 3.1 - General Ethernet Setup
Input Filter Sets=
Output Filter Sets=
Press ENTER to Confirm or ESC to Cancel: