Brother International HL-3075CW Network Users Manual - English - Page 20

Configuring your machine for a network, Overview, IP addresses, subnet masks and gateways - series

Get Brother International HL-3075CW PDF manuals and user guides View all Brother International HL-3075CW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Configuring your machine for a network2 2 Configuring your machine for a network 2 Overview 2 2 Before using your Brother machine in a network environment, you must install the Brother software and also configure the appropriate TCP/IP network settings on the machine itself. In this chapter, you will learn the basic steps required to print over the network using TCP/IP protocol. We recommend that you use the Brother installer on the Brother CD-ROM to install the Brother software as this will guide you through the software and network installation. Please follow the instructions in the supplied Quick Setup Guide. Note If you do not wish to, or are unable to use the automatic installer or any of Brother's software tools, you can also use the machine's control panel to change network settings. For more information, see Network menu on page 45. IP addresses, subnet masks and gateways 2 To use the machine in a networked TCP/IP environment, you need to configure its IP address and subnet mask. The IP address you assign to the print server must be on the same logical network as your host computers. If it is not, you must properly configure the subnet mask and the gateway address. IP address 2 An IP address is a series of numbers that identifies each device connected to a network. An IP address consists of four numbers separated by dots. Each number is between 0 and 255. „ Example: In a small network, you would normally change the final number. • 192.168.1.1 • 192.168.1.2 • 192.168.1.3 How the IP address is assigned to your print server: 2 If you have a DHCP/BOOTP/RARP server in your network (typically UNIX®, Linux or Windows® XP, Windows Vista®, Windows® 7 or Windows Server® 2003/2008 network) the print server will automatically obtain its IP address from that server. Note On smaller networks, the DHCP server may also be the Router. For more information on DHCP, BOOTP and RARP, see:Using DHCP to configure the IP address on page 120 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
10
2
2
Configuring your machine for a network2
Overview
2
Before using your Brother machine in a network environment, you must install the Brother software and also
configure the appropriate TCP/IP network settings on the machine itself. In this chapter, you will learn the
basic steps required to print over the network using TCP/IP protocol.
We recommend that you use the Brother installer on the Brother CD-ROM to install the Brother software as
this will guide you through the software and network installation. Please follow the instructions in the supplied
Quick Setup Guide
.
Note
If you do not wish to, or are unable to use the automatic installer or any of Brother’s software tools, you can
also use the machine’s control panel to change network settings.
For more information, see
Network menu
on page 45.
IP addresses, subnet masks and gateways
2
To use the machine in a networked TCP/IP environment, you need to configure its IP address and subnet
mask. The IP address you assign to the print server must be on the same logical network as your host
computers. If it is not, you must properly configure the subnet mask and the gateway address.
IP address
2
An IP address is a series of numbers that identifies each device connected to a network. An IP address
consists of four numbers separated by dots. Each number is between 0 and 255.
Example: In a small network, you would normally change the final number.
•
192.168.1.1
•
192.168.1.2
•
192.168.1.3
How the IP address is assigned to your print server:
2
If you have a DHCP/BOOTP/RARP server in your network (typically UNIX
®
, Linux or Windows
®
XP, Windows
Vista
®
, Windows
®
7 or Windows Server
®
2003/2008 network) the print server will automatically obtain its IP
address from that server.
Note
On smaller networks, the DHCP server may also be the Router.
For more information on DHCP, BOOTP and RARP, see:-
Using DHCP to configure the IP address
on page 120
Configuring your machine for a network
2