Cisco WS-C3560E-48PD-SF Hardware Installation Guide - Page 101

Connecting to DC Power

Get Cisco WS-C3560E-48PD-SF PDF manuals and user guides View all Cisco WS-C3560E-48PD-SF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 101 highlights

C A P P E N D I X Connecting to DC Power This appendix describes how to make DC power connections to the Catalyst 3560V2-24TS-SD switch. See "Switch Installation (24- and 48-Port Switches)" and "Switch Installation (8- and 12-Port Switches)" for instructions on installing the switch. Connecting to DC Power To connect the Catalyst 3560V2-24TS-SD switch to a DC-input power source, follow the steps in these sections: • Preparing for Installation, page C-2 • Grounding the Switch, page C-2 • Wiring the DC-Input Power Source, page C-5 Warning This unit is intended for installation in restricted access areas. A restricted access area can be accessed only through the use of a special tool, lock and key, or other means of security. Statement 1017 Note We recommend that you use 18 AWG copper wiring for Network Equipment Building Systems (NEBS) installation. This guideline follows the standard guidelines for DC power wiring in the Central Office. Note When an RPS is connected to the Catalyst 3560V2-24TS-SD switch, the switch is not NEBS compliant. Note The grounding architecture of this product is DC-isolated (DC-I). Caution To comply with the intrabuilding lightning surge requirements, intrabuilding wiring must be shielded, and the shield for the wiring must be grounded at both ends. OL-6337-07 Catalyst 3560 Switch Hardware Installation Guide C-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
C-1
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
APPENDIX
C
Connecting to DC Power
This appendix describes how to make DC power connections to the Catalyst 3560V2-24TS-SD switch.
See
“Switch Installation (24- and 48-Port Switches)”
and
“Switch Installation (8- and 12-Port
Switches)”
for instructions on installing the switch.
Connecting to DC Power
To connect the Catalyst 3560V2-24TS-SD switch to a DC-input power source, follow the steps in these
sections:
•
Preparing for Installation, page C-2
•
Grounding the Switch, page C-2
•
Wiring the DC-Input Power Source, page C-5
Warning
This unit is intended for installation in restricted access areas. A restricted access area can be
accessed only through the use of a special tool, lock and key, or other means of security.
Statement 1017
Note
We recommend that you use 18 AWG copper wiring for Network Equipment Building Systems (NEBS)
installation. This guideline follows the standard guidelines for DC power wiring in the Central Office.
Note
When an RPS is connected to the Catalyst 3560V2-24TS-SD switch, the switch is not NEBS compliant.
Note
The grounding architecture of this product is DC-isolated (DC-I).
Caution
To comply with the intrabuilding lightning surge requirements, intrabuilding wiring must be shielded,
and the shield for the wiring must be grounded at both ends.