Cisco WS-C3560E-48PD-SF Hardware Installation Guide - Page 46

Mounting the Switch on a Wall

Get Cisco WS-C3560E-48PD-SF PDF manuals and user guides View all Cisco WS-C3560E-48PD-SF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

Installing the Switch Chapter 2 Switch Installation (24- and 48-Port Switches) Mounting the Switch on a Wall For the best support of the switch and cables, make sure the switch is attached securely to wall studs or to a firmly attached plywood mounting backboard. Mount the switch with the front panel facing up, as shown in Figure 2-12. See the "Wall-Mounting" section on page 2-12 for the switches that can also mount with the front panel facing down. Warning Read the wall-mounting instructions carefully before beginning installation. Failure to use the correct hardware or to follow the correct procedures could result in a hazardous situation to people and damage to the system. Statement 378 Figure 2-12 Mounting the Switch on a Wall Catalyst 3750 SERIES 2X 13X 14X 2X 2X MODE STASCPKEDEUDPSLTXAMTASRTPRSSYST 97927 1 1 1 User-supplied screws After the switch is mounted in the rack: 1. Power on the switch. See the "Verifying Switch Operation" section on page 2-6. 2. Connect to a 10/100 or 10/100/1000 port, and run Express Setup. See the Catalyst 3560 Switch Getting Started Guide for instructions. To use the CLI setup program, see Appendix D, "Configuring the Switch with the CLI-Based Setup Program." 3. Connect to the front-panel ports. 2-14 Catalyst 3560 Switch Hardware Installation Guide OL-6337-07

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
2-14
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2
Switch Installation (24- and 48-Port Switches)
Installing the Switch
Mounting the Switch on a Wall
For the best support of the switch and cables, make sure the switch is attached securely to wall studs or
to a firmly attached plywood mounting backboard. Mount the switch with the front panel facing up, as
shown in
Figure 2-12
.
See the
“Wall-Mounting” section on page 2-12
for the switches that can also mount with the front panel
facing down.
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system.
Statement 378
Figure 2-12
Mounting the Switch on a Wall
After the switch is mounted in the rack:
1.
Power on the switch. See the
“Verifying Switch Operation” section on page 2-6
.
2.
Connect to a 10/100 or 10/100/1000 port, and run Express Setup. See the
Catalyst 3560 Switch
Getting Started Guide
for instructions. To use the CLI setup program, see
Appendix D,
“Configuring the Switch with the CLI-Based Setup Program.”
3.
Connect to the front-panel ports.
1
User-supplied screws
97927
Catalyst 3750
SERIES
SYST
RPS
MASTR
STAT
DUPLX
SPEED
STACK
MODE
1
1