Cisco WS-C3560E-48PD-SF Hardware Installation Guide - Page 53

Connecting to Fiber-Optic SFP Modules

Get Cisco WS-C3560E-48PD-SF PDF manuals and user guides View all Cisco WS-C3560E-48PD-SF manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Chapter 2 Switch Installation (24- and 48-Port Switches) Connecting the Switch to Compatible Devices Step 3 Reconfigure and reboot the connected device, if necessary. Step 4 Repeat Steps 1 through 3 to connect each device. Connecting to Fiber-Optic SFP Modules Warning Class 1 laser product. Statement 1008 Caution Do not remove the rubber plugs from the SFP module port or the rubber caps from the fiber-optic cable until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables from contamination and ambient light. Before connecting to the SFP module, be sure that you understand the port and cabling stipulations in the "Installation Guidelines" section on page 2-5. See Appendix B, "Connector and Cable Specifications," for information about the LC on the SFP module. Step 1 Remove the rubber plugs from the module port and fiber-optic cable, and store them for future use. Step 2 Insert one end of the fiber-optic cable into the SFP module port (see Figure 2-19). Figure 2-19 Connecting to a Fiber-Optic SFP Module Port 40 41 42 43 44 45 46 47 48 47X Catalyst 3560 SERIES PoE-48 1 3 48X 2 4 1 97931 1 LC connector Step 3 Step 4 Insert the other cable end into a fiber-optic connector on a target device. Observe the port status LED. • The LED turns green when the switch and the target device have an established link. • The LED turns amber while the STP discovers the network topology and searches for loops. This process takes about 30 seconds, and then the port LED turns green. OL-6337-07 Catalyst 3560 Switch Hardware Installation Guide 2-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
2-21
Catalyst 3560 Switch Hardware Installation Guide
OL-6337-07
Chapter 2
Switch Installation (24- and 48-Port Switches)
Connecting the Switch to Compatible Devices
Step 3
Reconfigure and reboot the connected device, if necessary.
Step 4
Repeat Steps 1 through 3 to connect each device.
Connecting to Fiber-Optic SFP Modules
Warning
Class 1 laser product.
Statement 1008
Caution
Do not remove the rubber plugs from the SFP module port or the rubber caps from the fiber-optic cable
until you are ready to connect the cable. The plugs and caps protect the SFP module ports and cables
from contamination and ambient light.
Before connecting to the SFP module, be sure that you understand the port and cabling stipulations in
the
“Installation Guidelines” section on page 2-5
. See
Appendix B, “Connector and Cable
Specifications,”
for information about the LC on the SFP module.
Step 1
Remove the rubber plugs from the module port and fiber-optic cable, and store them for future use.
Step 2
Insert one end of the fiber-optic cable into the SFP module port (see
Figure 2-19
).
Figure 2-19
Connecting to a Fiber-Optic SFP Module Port
Step 3
Insert the other cable end into a fiber-optic connector on a target device.
Step 4
Observe the port status LED.
•
The LED turns green when the switch and the target device have an established link.
•
The LED turns amber while the STP discovers the network topology and searches for loops. This
process takes about 30 seconds, and then the port LED turns green.
1
LC connector
40
41
42
43
44
45
46
47
48
47X
48X
Catalyst 3560
SERIES
PoE-48
1
2
3
4
97931
1