Dell Vostro 200 Owner's Manual - Page 141

Away Metal Plate on Remove the Media Card Reader from its packaging.

Get Dell Vostro 200 PDF manuals and user guides View all Dell Vostro 200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 141 highlights

4 Disconnect the FlexBay USB cable and the power cable from the back of the Media Card Reader and from the internal USB connector on the system board (see "System Board Components" on page 106). 5 Remove the two screws securing the Media Card Reader. 6 Slide the Media Card Reader out through the front of the computer. 7 If you are not reinstalling the Media Card Reader, replace the drive panel insert, as needed. 8 Replace the bezel (see "Replacing the Bezel" on page 125). 9 Replace the computer cover (see "Replacing the Computer Cover" on page 166). 10 Connect your computer and devices to electrical outlets, and then turn them on. Installing a Media Card Reader 1 Follow the procedures in "Before You Begin" on page 101. 2 Remove the computer cover (see "Removing the Computer Cover" on page 103). 3 Remove the bezel (see "Removing the Bezel" on page 123). 4 If this is a new card reader installation: • Remove the drive panel insert (see "Removing the FlexBay BreakAway Metal Plate" on page 138). • Remove the Media Card Reader from its packaging. 5 Gently slide the Media Card Reader into place in the FlexBay slot. 6 Align the screw holes in the Media Card Reader with the screw holes in the FlexBay. 7 Tighten the two screws to secure the Media Card Reader. NOTE: Ensure that the Media Card Reader is installed before the FlexBay cable is connected. 8 Connect the FlexBay USB cable to the back of the Media Card Reader and to the internal USB connector on the system board (see "System Board Components" on page 106). Removing and Installing Parts 141

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
Removing and Installing Parts
141
4
Disconnect the FlexBay USB cable and the power cable from the back of
the Media Card Reader and from the internal USB connector on the
system board (see "System Board Components" on page 106).
5
Remove the two screws securing the Media Card Reader.
6
Slide the Media Card Reader out through the front of the computer.
7
If you are not reinstalling the Media Card Reader, replace the drive panel
insert, as needed.
8
Replace the bezel (see "Replacing the Bezel" on page 125).
9
Replace the computer cover (see "Replacing the Computer Cover" on
page 166).
10
Connect your computer and devices to electrical outlets, and then turn
them on.
Installing a Media Card Reader
1
Follow the procedures in "Before You Begin" on page101.
2
Remove the computer cover (see "Removing the Computer Cover" on
page 103).
3
Remove the bezel (see "Removing the Bezel" on page 123).
4
If this is a new card reader installation:
•
Remove the drive panel insert (see "Removing the FlexBay Break-
Away Metal Plate" on page 138).
•
Remove the Media Card Reader from its packaging.
5
Gently slide the Media Card Reader into place in the FlexBay slot.
6
Align the screw holes in the Media Card Reader with the screw holes in the
FlexBay.
7
Tighten the two screws to secure the Media Card Reader.
NOTE:
Ensure that the Media Card Reader is installed before the FlexBay cable is
connected.
8
Connect the FlexBay USB cable to the back of the Media Card Reader and
to the internal USB connector on the system board (see "System Board
Components" on page 106).