HP Color LaserJet CM4730 HP LaserJet MPF Products - Configuring Security for M - Page 47

Configurations on the Security

Get HP Color LaserJet CM4730 - Multifunction Printer PDF manuals and user guides View all HP Color LaserJet CM4730 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Note: The Access Control List options appear next on the Network page, but you should have already configured this. The ACL instructions appear in the Initial Settings section of this chapter to help ensure security during the time you are configuring the MFPs. 9. Click to select Protocol Stacks (Figure 45), and deselect all unused protocol stacks as applicable to your network. See the table below. Figure 45: The Protocol Stacks option. The following table lists each protocol with the recommended setting and an explanation: Protocol Stack IPX/SPX Recommended Setting Leave blank to disable Explanation This setting disables access for Novell servers. TCP/IP Select to enable This is the normal operating protocol for the MFPs. DLC/LLC Select to enable This setting enables the MFP to communicate at basic levels on the network. AppleTalk Leave blank to disable This protocol provides access to older Apple and Macintosh computers. It should be disabled if not in use. 10. Select the devices to configure in the Device List, and click Configure Devices. The View Log page will appear to show the status of the configurations. Click Refresh to update the status. Once the View Log page shows success, click Go Back to continue. Configurations on the Security page The Security Configuration page lists options that are important to MFP security. 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Note:
The Access Control List options appear next on the Network page, but you
should have already configured this. The ACL instructions appear in the
Initial Settings section of this chapter to help ensure security during the time
you are configuring the MFPs.
9.
Click to select
Protocol
Stacks
(Figure 45), and deselect all unused protocol stacks as
applicable to your network. See the table below.
Figure 45: The Protocol Stacks option.
The following table lists each protocol with the recommended setting and an explanation:
Protocol Stack
Recommended Setting
Explanation
IPX/SPX
Leave blank to disable
This setting disables access for
Novell servers.
TCP/IP
Select to enable
This is the normal operating protocol
for the MFPs.
DLC/LLC
Select to enable
This setting enables the MFP to
communicate at basic levels on the
network.
AppleTalk
Leave blank to disable
This protocol provides access to
older Apple and Macintosh
computers. It should be disabled if
not in use.
10.
Select the devices to configure in the
Device
List
, and click
Configure
Devices
. The
View
Log
page will appear to show the status of the configurations. Click
Refresh
to update the status.
Once the
View
Log
page shows success, click
Go
Back
to continue.
Configurations on the Security page
The
Security
Configuration
page lists options that are important to MFP security.
7