HP DL760 ProLiant DL760 Generation 2 Server Maintenance and Service Guide - Page 76

I/O Module Removal and Replacement Procedures, I/O Module

Get HP DL760 - ProLiant - G2 PDF manuals and user guides
UPC - 613326397428
View all HP DL760 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 76 highlights

6 I/O Module Removal and Replacement Procedures I/O Module The I/O module is located at the rear of the server. Remove it to replace or service non-hot-plug components or to access other components in the I/O module. IMPORTANT: You must re-enter the server serial number through RBSU after you replace the I/O module. Refer to the "Re-entering the Server Serial Number" section in Chapter 2. Removing the Cable Management Arm: To remove the cable management arm: 1. Label all cables running through the cable management arm. 2. Disconnect all cables from the rear of the I/O module. 3. Loosen thumbscrew that secures the cable management arm and bracket to the I/O module (1). 4. Move the bracket, with cable management arm attached, slightly up and then back from the server (2) so that it is possible to access the cam levers on the I/O module. HP ProLiant DL760 Generation 2 Server Maintenance and Service Guide 6-1 HP CONFIDENTIAL Codename: Jed Part Number: 201262-003 Last Saved On: 2/10/04 4:10 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
6
I/O Module Removal and Replacement Procedures
I/O Module
The I/O module is located at the rear of the server. Remove it to replace or service
non-hot-plug components or to access other components in the I/O module.
IMPORTANT:
You must re-enter the server serial number through RBSU after you replace the I/O
module. Refer to the “Re-entering the Server Serial Number” section in Chapter 2.
Removing the Cable Management Arm:
To remove the cable management arm:
1.
Label all cables running through the cable management arm.
2.
Disconnect all cables from the rear of the I/O module.
3.
Loosen thumbscrew that secures the cable management arm and bracket to the I/O
module (1).
4.
Move the bracket, with cable management arm attached, slightly up and then back from
the server (2) so that it is possible to access the cam levers on the I/O module.
HP ProLiant DL760 Generation 2 Server Maintenance and Service Guide
6-1
HP CONFIDENTIAL
Codename: Jed Part Number: 201262-003 Last Saved On: 2/10/04 4:10 PM