HP DL760 ProLiant DL760 Generation 2 Server Maintenance and Service Guide - Page 89

Adding PCI Hot Plug Expansion Boards, Open the I/O lid. - quickspecs

Get HP DL760 - ProLiant - G2 PDF manuals and user guides
UPC - 613326397428
View all HP DL760 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

I/O Module Removal and Replacement Procedures Adding PCI Hot Plug Expansion Boards The PCI/PCI-X slots of the ProLiant DL760 G2 I/O board are hot-plug-capable and support a variety of industry-standard expansion boards. NOTE: For a list of supported I/O expansion boards, refer to the HP QuickSpecs for the HP ProLiant DL760 G2 servers: www.hp.com Refer to Figure 6-10, Figure 6-11, and Table 6-2 for definitions of the PCI Hot Plug LEDs. To add a PCI/PCI-X expansion board into PCI Hot Plug slots 1 through 11: 1. Open the I/O lid. 2. If the PCI Hot Plug green LED is on, power down the slot by pressing the PCI Hot Plug button corresponding to the slot or by using a PCI Hot Plug software application. Wait until the green LED is off. CAUTION: To avoid system power-down and subsequent data loss, do not open the slot release lever unless the green PCI Hot Plug LED of the slot is off. NOTE: The PCI Hot Plug Button allows you to press the button again within five seconds of the first press to cancel the action. 3. Press on the top of the appropriate expansion slot release lever (1) and open the lever toward the rear of the expansion slot (2). 4. Remove the expansion slot cover (3). Figure 6-12: Preparing the hot-plug expansion slot for installation 6-14 HP ProLiant DL760 Generation 2 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Jed Part Number: 201262-003 Last Saved On: 2/10/04 4:10 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
I/O Module Removal and Replacement Procedures
Adding PCI Hot Plug Expansion Boards
The PCI/PCI-X slots of the ProLiant DL760 G2 I/O board are hot-plug-capable and support a
variety of industry-standard expansion boards.
NOTE:
For a list of supported I/O expansion boards, refer to the HP QuickSpecs for the HP ProLiant
DL760 G2 servers:
www.hp.com
Refer to Figure 6-10, Figure 6-11, and Table 6-2 for definitions of the PCI Hot Plug LEDs.
To add a PCI/PCI-X expansion board into PCI Hot Plug slots 1 through 11:
1.
Open the I/O lid.
2.
If the PCI Hot Plug green LED is on, power down the slot by pressing the PCI Hot Plug
button corresponding to the slot or by using a PCI Hot Plug software application. Wait
until the green LED is off.
CAUTION:
To avoid system power-down and subsequent data loss,
do not
open the slot
release lever unless the green PCI Hot Plug LED of the slot is off.
NOTE:
The PCI Hot Plug Button allows you to press the button again within five seconds of the first
press to cancel the action.
3.
Press on the top of the appropriate expansion slot release lever (1) and open the lever
toward the rear of the expansion slot (2).
4.
Remove the expansion slot cover (3).
Figure 6-12: Preparing the hot-plug expansion slot for installation
6-14
HP ProLiant DL760 Generation 2 Server Maintenance and Service Guide
HP CONFIDENTIAL
Codename: Jed Part Number: 201262-003 Last Saved On: 2/10/04 4:10 PM