HP DL760 ProLiant DL760 Generation 2 Server Maintenance and Service Guide - Page 83

Non-Hot Plug Expansion Boards, Removing a Non-Hot Plug Expansion board

Get HP DL760 - ProLiant - G2 PDF manuals and user guides
UPC - 613326397428
View all HP DL760 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

I/O Module Removal and Replacement Procedures Non-Hot Plug Expansion Boards CAUTION: Do not open the slot release lever unless the green PCI Hot Plug LED indicator is off. System power down and subsequent data loss could occur. To remove a non-hot plug expansion board: 1. Power down the server. Refer to "Pow ering Down the Server" in Chapter 2. 2. Slide the server out of the rack. 3. Open the I/O lid. Refer to "I/O Lid" in Chapter 3. 4. Remove any expansion board I/O cables as appropriate. 5. Press down on the top of the expansion slot release lever (1) and push the lever up (2). 6. Unseat the expansion board by pulling up on the plastic tab (3) and lift the board out of the server (4). For full-length boards, take care to not force the board out of the slot keeper. Refer to Figure 6-9. IMPORTANT: If you are only removing the expansion board, install an expansion slot cover in the slot. Figure 6-7: Removing a Non-Hot Plug Expansion board 6-8 HP ProLiant DL760 Generation 2 Server Maintenance and Service Guide HP CONFIDENTIAL Codename: Jed Part Number: 201262-003 Last Saved On: 2/10/04 4:10 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
I/O Module Removal and Replacement Procedures
Non-Hot Plug Expansion Boards
CAUTION:
Do not open the slot release lever unless the green PCI Hot Plug LED indicator is
off. System power down and subsequent data loss could occur.
To remove a non-hot plug expansion board:
1.
Power down the server. Refer to “Pow ering Down the Server” in Chapter 2.
2.
Slide the server out of the rack.
3.
Open the I/O lid. Refer to “I/O Lid” in Chapter 3.
4.
Remove any expansion board I/O cables as appropriate.
5.
Press down on the top of the expansion slot release lever (1) and push the lever up (2).
6.
Unseat the expansion board by pulling up on the plastic tab (3) and lift the board out of
the server (4). For full-length boards, take care to not force the board out of the slot
keeper. Refer to Figure 6-9.
IMPORTANT:
If you are only removing the expansion board, install an expansion slot cover in the slot.
Figure 6-7:
Removing a Non-Hot Plug Expansion board
6-8
HP ProLiant DL760 Generation 2 Server Maintenance and Service Guide
HP CONFIDENTIAL
Codename: Jed Part Number: 201262-003 Last Saved On: 2/10/04 4:10 PM