Invacare 3GAR Owners Manual 2 - Page 125

Securing the Occupant

Get Invacare 3GAR PDF manuals and user guides View all Invacare 3GAR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

Securing the Occupant SECTION 17-TRANSPORT READY PACKAGE Wheelchair-Anchored Belts ƽ WARNING The pelvic belt that is provided by Invacare has been tested for use in a motor vehicle on this wheelchair ONLY. DO NOT replace the pelvic belt with a different style pelvic belt. NOTE: For this procedure, refer to FIGURE 17.2 on page 126. The wheelchair has been provided with a pelvic belt which meets the requirements of ANSI/RESNA W/C 19. The pelvic belt, provided by Invacare, has been designed to accommodate use on either side of the vehicle. If necessary, follow the instructions below to reverse the orientation of the pelvic belt to accommodate the vehicle-anchored upper-torso belt. 1. Install the pelvic belt pin (Detail "A" of FIGURE 17.2) into the large end of the slot in the belt mounting bracket. Rotate downward and forward until it snaps into place into the small end of the slot (Detail "B" or Detail "C"). NOTE: Note the position of the male end of the belt when installing the pelvic belt onto the belt mounting brackets. The male end of the pelvic belt (DETAIL "A" of FIGURE 17.2) has a pin which is used to secure the vehicle-anchored upper-torso belt. 2. Repeat STEP 1 for the opposite belt mounting bracket. 3. Install the vehicle-anchored upper-torso belt onto the pin on the male end of the pelvic belt. Part No 1134791 125 3G Storm Series® Wheelchairs

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
SECTION 17—TRANSPORT READY PACKAGE
Part No 1134791
125
3G Storm Series® Wheelchairs
Securing the Occupant
Wheelchair-Anchored Belts
±
WARNING
The pelvic belt that is provided by Invacare has been tested for use in a motor vehi-
cle on this wheelchair ONLY. DO NOT replace the pelvic belt with a different style
pelvic belt.
NOTE: For this procedure, refer to FIGURE 17.2 on page 126.
The wheelchair has been provided with a pelvic belt which meets the requirements of
ANSI/RESNA W/C 19.
The pelvic belt, provided by Invacare, has been designed to accommodate use on either
side of the vehicle. If necessary, follow the instructions below to reverse the orientation of
the pelvic belt to accommodate the vehicle-anchored upper-torso belt.
1.
Install the pelvic belt pin (Detail "A" of FIGURE 17.2) into the large end of the slot in
the belt mounting bracket. Rotate downward and forward until it snaps into place into
the small end of the slot (Detail “B” or Detail “C”).
NOTE: Note the position of the male end of the belt when installing the pelvic belt onto the belt
mounting brackets. The male end of the pelvic belt (DETAIL "A" of FIGURE
17.2) has a pin which
is used to secure the vehicle-anchored upper-torso belt.
2.
Repeat STEP 1 for the opposite belt mounting bracket.
3.
Install the vehicle-anchored upper-torso belt onto the pin on the male end of the pelvic
belt.