Invacare 3GAR Owners Manual 2 - Page 83

Adjusting Reclining Armrest Height

Get Invacare 3GAR PDF manuals and user guides View all Invacare 3GAR manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

SECTION 7-ARMS Adjusting Reclining Armrest Height NOTE: For this procedure, refer to FIGURE 7.6. NOTE: This procedure applies to 2G Tarsys seating systems only. 1. Make sure the seating system is in the full upright position. Refer to Operating Powered Seating Systems on page 50. 2. Remove the socket bolt and locknut that secure the front of the upper armrest to the lower armrest. 3. Loosen, but DO NOT remove, the two socket screws that secure the rear of the armrest of the back cane. 4. Adjust the armrest to the desired height for the user. NOTE: The armrests can be at different heights to accommodate the user. NOTE: The armrest adjusts from 11 to 16 inches in 1-inch increments. 5. Reinstall the socket bolt through the mounting hole determined in STEP 4. 6. Reinstall the locknut and tighten securely. 7. While holding the armrest level, tighten the two socket screws that secure the rear of the armrest to the back cane. 8. Repeat STEPS 2-7 for the opposite side if necessary. Socket Screws Armrest Back Cane Locknut Socket Bolt Height Adjustment Holes FIGURE 7.6 Adjusting Reclining Armrest Height Part No 1134791 83 3G Storm Series® Wheelchairs

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
SECTION 7—ARMS
Part No 1134791
83
3G Storm Series® Wheelchairs
Adjusting Reclining Armrest Height
NOTE: For this procedure, refer to FIGURE 7.6.
NOTE: This procedure applies to 2G Tarsys seating systems only.
1.
Make sure the seating system is in the full upright position.
Refer to Operating
Powered Seating Systems
on page 50
.
2.
Remove the socket bolt and locknut that secure the front of the upper armrest to the
lower armrest.
3.
Loosen, but DO NOT remove, the two socket screws that secure the rear of the armrest
of the back cane.
4.
Adjust the armrest to the desired height for the user.
NOTE: The armrests can be at different heights to accommodate the user.
NOTE: The armrest adjusts from 11 to 16 inches in 1-inch increments.
5.
Reinstall the socket bolt through the mounting hole determined in STEP 4.
6.
Reinstall the locknut and tighten securely.
7.
While holding the armrest level, tighten the two socket screws that secure the rear of
the armrest to the back cane.
8.
Repeat STEPS 2-7 for the opposite side if necessary.
FIGURE 7.6
Adjusting Reclining Armrest Height
Armrest
Back Cane
Socket
Screws
Socket Bolt
Height Adjustment
Holes
Locknut