Linksys SPA922 Cisco SPA9000 Voice System Using Setup Wizard Installation and - Page 56

STEP 1, Main Menu - default admin password

Get Linksys SPA922 - IP Phone With Switch PDF manuals and user guides
UPC - 745883570836
View all Linksys SPA922 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Connecting the Equipment Connecting and Configuring the Equipment (New Installation) 4 STEP 1 Follow the instructions on the page to connect one to four SPA400 devices to the switch. • If you are not connecting a SPA400 at this time, click Skip to bypass the SPA400 installation steps. The Main Menu appears. Continue to the procedure "Configuring the SPA9000," on page 57. • Connect an Ethernet cable from the SPA400 ETHERNET port to an available port on your switch. The port must be configured with the Qos and CoS settings described in "Configuring the Switch," on page 40. • If you are using a SPA400 for voice mail, insert the provided 128MB USB 2.0 flash drive into the SPA400 USB port before powering on the SPA400. • Where multiple SPA400 units are installed, use only one unit for voice mail. The other units do not require the USB flash drive, which you can reuse for other purposes. • The SPA400 device takes significantly longer to power up than does the SPA9000. Wait at least 2 minutes after powering the SPA400 before you click the Next button. STEP 2 Click Next to cause the Wizard to discover all SPA400 devices that are connected to the network. STEP 3 Wait as the progress messages appear on the PC screen. The following alerts may appear: • You have no SPA400s connected in your network. This message may appear if the SPA400 was not fully booted up when the Wizard began the auto-detection process or if the Wizard is running on a computer that is not on the same local network as the SPA9000. Click OK to close the message. After you resolve the issues, click Next to cause the Wizard to auto-dectect the SPA400 devices. Then continue with this procedure. • SPA400 password needed. This message appears if the SPA400 previously was configured with a password. Enter the password, and then click OK. (By default, the SPA400 has no password, so this message should not appear if you are installing a new device.) The Wizard expects the SPA400 administrative user name to be the default Admin with a capital A. SPA9000 Voice System Installation and Configuration Guide for Setup Wizard 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
Connecting the Equipment
Connecting and Configuring the Equipment (New Installation)
SPA9000 Voice System Installation and Configuration Guide for Setup Wizard
54
4
STEP 1
Follow the instructions on the page to connect one to four SPA400 devices to the
switch.
•
If you are not connecting a SPA400 at this time, click
Skip
to bypass the
SPA400 installation steps. The
Main Menu
appears. Continue to the procedure
“Configuring the SPA9000,” on page 57
.
•
Connect an Ethernet cable from the SPA400 ETHERNET port to an available
port on your switch. The port must be configured with the Qos and CoS
settings described in
“Configuring the Switch,” on page 40
.
•
If you are using a SPA400 for voice mail, insert the provided 128MB USB 2.0
flash drive into the SPA400 USB port before powering on the SPA400.
•
Where multiple SPA400 units are installed, use only one unit for voice mail. The
other units do not require the USB flash drive, which you can reuse for other
purposes.
•
The SPA400 device takes significantly longer to power up than does the
SPA9000. Wait at least 2 minutes after powering the SPA400 before you click
the Next button.
STEP 2
Click
Next
to cause the Wizard to discover all SPA400 devices that are connected
to the network.
STEP 3
Wait as the progress messages appear on the PC screen.
The following alerts may appear:
•
You have no SPA400s connected in your network.
This message may appear if the SPA400 was not fully booted up when the
Wizard began the auto-detection process or if the Wizard is running on a
computer that is not on the same local network as the SPA9000. Click
OK
to
close the message. After you resolve the issues, click
Next
to cause the Wizard
to auto-dectect the SPA400 devices. Then continue with this procedure.
•
SPA400 password needed.
This message appears if the SPA400 previously was configured with a
password. Enter the password, and then click
OK
. (By default, the SPA400 has
no password, so this message should not appear if you are installing a new
device.)
The Wizard expects the SPA400 administrative user name to be the default
Admin
with a capital A.