Linksys SPA922 Cisco SPA9000 Voice System Using Setup Wizard Installation and - Page 61

Configuring a Static IP Address on the SPA9000 (If Prompted), evice is, con d to use DHCP

Get Linksys SPA922 - IP Phone With Switch PDF manuals and user guides
UPC - 745883570836
View all Linksys SPA922 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Connecting the Equipment Configuring the SPA9000 4 This message may occur for the following reasons: • The network cable is disconnected from the SPA9000 INTERNET port or the switch port. Check the cables to ensure that the SPA9000 is properly connected to the switch. • The Wizard is running on a computer that is not on the same local network as the SPA9000. Check the IP address of the administration computer. • WAN access is not enabled on the SPA9000. This issue should not occur with a new device, where WAN access is enabled by default, but may occur on a device that was configured previously. Follow the instructions on the screen to ensure that WAN access is enabled and to learn the IP address of the SPA9000. • After correcting any errors that you find, click Back to return to the previous screen. Then click Next, and the Wizard attempts to discover the SPA9000. NOTE If the Manually Input SPA9000 IP Address screen appears after you complete these troubleshooting steps, enter the IP address, and then click Next to continue. Configuring a Static IP Address on the SPA9000 (If Prompted) The Wizard tests the SPA9000 device to verify that it is configured with a static IP address in order to ensure professional-grade uptime. The SPA9000 device would not be able to provide PBX functions to devices that cannot locate it if its IP address was changed by a DHCP server. Complete this procedure if the Wizard displays the following message: Device is configured to use DHCP. SPA9000 Voice System Installation and Configuration Guide for Setup Wizard 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
Connecting the Equipment
Configuring the SPA9000
SPA9000 Voice System Installation and Configuration Guide for Setup Wizard
59
4
This message may occur for the following reasons:
•
The network cable is disconnected from the SPA9000 INTERNET port or the
switch port. Check the cables to ensure that the SPA9000 is properly
connected to the switch.
•
The Wizard is running on a computer that is not on the same local network as
the SPA9000. Check the IP address of the administration computer.
•
WAN access is not enabled on the SPA9000. This issue should not occur with a
new device, where WAN access is enabled by default, but may occur on a
device that was configured previously. Follow the instructions on the screen to
ensure that WAN access is enabled and to learn the IP address of the
SPA9000.
•
After correcting any errors that you find, click
Back
to return to the previous
screen. Then click
Next
, and the Wizard attempts to discover the SPA9000.
NOTE
If the Manually Input SPA9000 IP Address screen appears after you complete these
troubleshooting steps, enter the IP address, and then click
Next
to continue.
Configuring a Static IP Address on the SPA9000 (If
Prompted)
The Wizard tests the SPA9000 device to verify that it is configured with a static IP
address in order to ensure professional-grade uptime. The SPA9000 device would
not be able to provide PBX functions to devices that cannot locate it if its IP
address was changed by a DHCP server.
Complete this procedure if the Wizard displays the following message:
D
evice is
configured to use DHCP
.