Netgear GSM7248v1 GSM7224 Administration manual - Page 69

Virtual Router Redundancy Protocol

Get Netgear GSM7248v1 - ProSafe 48 Port Layer 2 Gigabit L2 Ethernet Switch PDF manuals and user guides View all Netgear GSM7248v1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Chapter 8 Virtual Router Redundancy Protocol When an end station is statically configured with the address of the router that will handle its routed traffic, a single point of failure is introduced into the network. If the router goes down, the end station is unable to communicate. Since static configuration is a convenient way to assign router addresses, Virtual Router Redundancy Protocol (VRRP) was developed to provide a backup mechanism. VRRP eliminates the single point of failure associated with static default routes by enabling a backup router to take over from a "master" router without affecting the end stations using the route. The end stations will use a "virtual" IP address that will be recognized by the backup router if the master router fails. Participating routers use an election protocol to determine which router is the master router at any given time. A given port may appear as more than one virtual router to the network, also, more than one port on a 7000 Series Managed Switch may be configured as a virtual router. Either a physical port or a routed VLAN may participate. 8-1 v1.0, Jan 2007

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
8-1
v1.0, Jan 2007
Chapter 8
Virtual Router Redundancy Protocol
When an end station is statically configured with the address of the router that will handle its
routed traffic, a single point of failure is introduced into the network. If the router goes down, the
end station is unable to communicate. Since static configuration is a convenient way to assign
router addresses, Virtual Router Redundancy Protocol (VRRP) was developed to provide a backup
mechanism.
VRRP eliminates the single point of failure associated with static default routes by enabling a
backup router to take over from a “master” router without affecting the end stations using the
route. The end stations will use a “virtual” IP address that will be recognized by the backup router
if the master router fails. Participating routers use an election protocol to determine which router is
the master router at any given time. A given port may appear as more than one virtual router to the
network, also, more than one port on a 7000 Series Managed Switch may be configured as a virtual
router. Either a physical port or a routed VLAN may participate.